We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
We have constructed a custom board of nRF52832 via I2C communication with sensor and INT based wake up. Following configuration enable
DCDC Power Enable
Disconnected...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
I am trying to use my nRF51 Dongle (pca10031) as a central.
I downloaded the nRF5_SDK_12.3.0_d7731ad and I could see that there is no BLE project for pca10031 (only pca10028...
i used nRF5_SDK_14.1.0_1dda907.
ANT protocol :
I used ant_background_scanning example.
I want to scannig device ID of hrm, bpwrt and bsc.
Then choose the device ID...
Looking forward to using the new sdk v15! Is there a plan to implement a new Bluetooth Developer studio plugin or should we go ahead and keep using the current version? We...
Hi, I encountered the following error in keil v5.12.0.0:
linking... .\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol nrf_drv_gpiote_in_event_enable (referred...
Hi,
During SD+BL OTAU form SD132 ver 3.1.0 to SD112 ver 5.1.0, Old bootloader copied new one using function nrf_dfu_mbr_copy_bl(uint32_t * p_src, uint32_t len); to bad address...
Hi,
I have nrf52840 DK, I am unable to find details of which debug pin connected connected to respective controller pin.
basically dev kit has 10pin "Debug input" I want...
I tried following steps as mentioned in the tutorial, but after adding " ../../../../../../components/device " to the User Include Directories it looked like this..
But...
Hi,
I successfully installed and test pc-ble-driver with connectivity_2.0.1_115k2_with_s132_5.0.hex on PCA10040.
When I download ble_connectivity_s132_uart_pca10040.hex...
Android nRF Connect app DFU is flakey on my phone, a Motorola Droid Turbo w/Android 6.0.1. I tried with a Moto X and it worked fine, but on my Droid it rarely downloads successfully...
I'm using 52832/S132 V2/SDK11. For the test I only send notification to central just to see how many I can send in each interval. I keep calling sd_ble_gatts_hvx() until I...
