Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I have a project with 52810 which I use rc for LF clock source and I need use P00 and P01 as general GPIO, I have set both CLOCK_CONFIG_XTAL_FREQ and NRF_SDH_CLOCK_LF_SRC...
We are developing an nRF52832-based circuit with 1.8v power supply, which features BLE, NFC, SAADC, I2C & SPI.
According to datasheets, all 3rd party components are also...
Hi,
we plan to use the nRF52832 for a new project, I have two questions:
LE secure is supported, is this right ?
We want to pair up to 8 phones with our device....
Hi,
I am using SDK 14.2 with nrf52840 board. In my project I am using USB and BLE together. I have noticed that when I enable the LE Secure pairing and after that my USB...
Which nrfutil version should be used with Mesh SDK?
Getting started for Mesh has the link to nfrutil verison 0.3.0.0. In pc-nrfutil github repo the latest version is 3.5...
Hi!
I try to do simple led blink on nrf51822 and after build i got this:
Checking project status
Building ‘dongle’ from solution ‘dongle’ in configuration ‘Debug’
Compiling...
Hi,
I am using Segger IDE and now I wanna to use the temperature sensor presents in the PCA10040 board.
I tested the SDK example using the keil and works fine. When I...
I have your NRF52 DK and beacons.
I want to make the case so that my Nordic NRF52 DK will get data from Nordic beacons and forwarded that data on the UART port of PC....
Hi there,
I am developing a BLE dongle, and a BLE peripheral both based on NRF51822QFAC. The BLE dongle scans, connects, and disconnects the BLE peripheral by UART commands...
Hi
I get the following compiler (assembler) error in my project:
... Compiling file: hardfault_handler_gcc.c /tmp/ccstUNqW.s: Assembler messages: /tmp/ccstUNqW.s:46: Error...
Hey All,
I'm using the nrf_drv_uart UARTE driver (NRF52832) communicating with an external device. The UART init code is executed using a function (call all_main in this...
Hello All,
I am working on NFC using nRF52832 chipset .
I followed the below this link for http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi everyone :D
I'm not being able to compile a c++ code on segger embedded studio.
The same code compiles with the Makefile provided in the SDK 14.2, but not with the...
Hey, we are using the nrf52840, and the SDK 14.0.2 and the uart example. We need to set the BLE range to max, and therefor the TX to 8db, the transfer speed to 125kb/s. We...
