Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
Hi there,
I'm about to develop my first BLE product and got my eyes on the nRF52840.
My product should be able to do the following:
1. Continuously read high rate data...
Hi All
I'm trying to measure the Ton and the Toff of a signal present on an input pin of a nRF51822.
The idea is to use PPI, Timer 1 and save timer on every falling/rising...
Hi,
we are using Linux machine and my application is running init, blue tooth stack is running on nrf52 board but after initiating the scan command we are not getting continuous...
Hi all,
I am using a linux based board and wanted to support BLE5.0 on that board. PCA10040 is connected with My board through UART. Please forgive me for these basic doubts...
Hi All,
Moto E4 mobile phones do not connect right away and at times takes few minutes and connects eventually. Right after I hit connect I get an error 0x85(GATT ERROR...
I am using Thingy (nrf52832) to advertise Eddystone UID and TLM packets in bursts. On a given event advertising starts with an interval of 200ms, then stops after specified...
My SPIM0 starts to use 300uA upon first usage of nrf_drv_spi_transfer. Why? Even when the transfer finishes and I uninitialize SPI or turn the MOSI, MISO and CLK pins to the...
Hi there ..
I have question regarding estimation of a coin cell battery life while advertising on nrf52840 PDK. I followed here https://devzone.nordicsemi.com/b/blog/posts...
Hello,
I am fairly new to developing ble beacon applications and was wondering if it was possible for my device to perform the following operations simultaneously:
Advertise...
Hello, my project is not going well. Trouble you Please help me again First of all, my English is not very good. I'm sorry. Can you provide an ideal sample code for me? My...
Hi
I'm using SDK 14.2, nrf52 DK and proximity example. When i try to write to inmediatte alert characteristic from nrf Connect ( android) i never get the event on the device...
Hi, in my project, the following codes caused "NRF_BREAKPOINT_COND":
sd_power_ram_power_set(4,(POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos) | (POWER_RAM_POWER_S1POWER_On...
I have secure DFU working fine for my s132 (SES sdk15.0), and now trying s112 using the example from post how to use dfu?
I used SDK_14.2.0_nRF52810_Secure_BL_v1.1.zip and...
