Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello,
Recently i am working on UART application on nRF51822 based product.
In UART application code, there is no option to configure the modulation rate.
So, I would...
Dear friends,
if i adjust the tx power of nRF52832, e.g., by calling sd_ble_gap_tx_power_set(), which phase of the current will be affected in the pic bellow? just the phase...
I am struggling with getting a Secure UART(Serial) DFU operation to function correctly when I attempt to enter the bootloader with a call from my app. I am using the basic...
Hi all,
I am working on interfacing an SD card as well as an OLED Display with my nrf51422 on SDK 12.2.0.
Although, both are on SPI and hence i need to configure them...
Hello,
I'm running the SPIS example from Keil (SDK 15.0), but I want to print out the received as the decimal value instead of as a string. If I change %s to a %d in this...
I cannot access any more my nRF52 DK 10040 with nrfjprog ,indipendently from the command I give.
I use Windows10 nrfjprog command line ,i can see and access JLINK drive...
Hi,
I am using two nRF52832 and one nRF24L01+.
My topology is as follows: nRF52832 A<---> nRF52832 B<---> nRF24L01+.
where "A <---> B" means that A communicate with...
To check, in sdk 15.0, there are no pca10040e (s112) examples of ble_app_buttonless_dfu & secure_bootloader because examples were not yet ready for sdk 15.0 release, or something...
Hello,
I'm currently using the nRF52832 chips with SDK11.0.0 and s132. I'm currently trying to modify the TX power level for advertisement. I'm seeing many ways that I could...
HI, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v2.0.0) and some other sensors which drivers written by using nRF5_SDK_15.0.0 . Can you help to understand how to do...
Is it possible to program the nRF52840 dongle using the nRF52840-DK using SWD?
I tried, but it failed. From the nRF52840 schematic, it looks the chip is running at 1.8V...
Hi,
Win10 can run a subsystem, which is Ubuntu for me, in the powershell environmental.
But I can not connect the pca10040 debugger. it show error when I try to erase...
I am trying to build a run time test routine that will return the ppm offset between the 32khz and the 16mhz clocks.
Can i use PPI to hook 10 clocks 32khz ticks to capture...
Hi,
MY pca10056 dev board is no longer getting detected. i have gone through this post
here is what i have checked ,
Does the device show up in Device Manager?
No...
