I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi.
I'm busy to add the nrf8001 BLE module to my PIC32MM product for negative pressure monitoring in a small area. Is there is list of minimum settings that is available...
Hello,
I'm having issues with the advertising module in SDK 15.0. I basically want the device to fast advertise for 3 minutes and then switch to slow advertising forever...
When I configured POWER_CONFIG_DEFAULT_DCDCEN =1, I found almost no change compared to the case of dcdc, but when I added APP_ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Quite a generic FreeRTOS question probably here but... on an interrupt, what's the stack the ISR uses? Is it the one from the stack that got interrupted? If so, I guess that...
HI!
I'm using two nRF52840 boards to communicate using ESB. The ESB API doesn't have a pairing protocol so I figured I'd write one without encryption or any bells and...
Hi all,
when I insert ble_nus into mesh_gatt . I realized there are two pulse functions with the same function:
and
if they let them coexist , when I use nrf_connect...
Hi
Using the iOS 'nrf Mesh' application I can provision a PCA10056 succesfully.
I have written fimware image that sniffs for mesh related becaons, and when I power up...
I want advertise data only change with uuid for every 100ms I gone through the nrf 51power consumption guide I guess its same for nrf52 any help for changes or must have points...
Hi,
I'm using multilink Central device with SDK9.0 and stack S130. I'm able to connect to multilink peripheral device as expected. But i am not able to connect to a Custom...
Hi, is it possible to check the current configuration of a GPIO pin? I mean if the pin is currently configured as input or output. Next I need to uninitialize it and reinitialize...
Hi,
the Nordic nRF-series SoCs have got the restriction, that the power has to rise from 0 V to 1.7 V in 60 ms for a guaranteed POR. In our application we cannot guarantee...
We use nRF52832 on our product. We need to update the application remotely in the field using smartphone with BT. The unit in the field will already have an app running on...
Hi,
I'm working on treating the nrf as a CDC ACM device and in order to test it I've been using a script to send input to the chip through echo commands to the /dev/ttyACM...
Hey, can you say me, how can I switch on of the Node-Features (relay, proxy, friend) with help of the Interactive mesh provisioning and configuration Script pyACI.
