Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi,
We are using nRF24L01+ modules on an ultrasonic positioning system. For synchronization, we wanted to use the RX and TX interrupts provided by the module to trigger...
Hi.
I'm currently trying to scan non-connectable advertisement for continuously.
it’s unclear to me. I doubt will be worked scanning 1000 peripherals.
so. i have to...
We are devolping a module with nRF52832-CIAA (CSP package) and we are not satisfied with the sensitivity.
According to the nRF52832 Errata is the sensitivity level different...
Dear all members,
I understand that Secure BLE DFU official support is only for SD132, but I am developing a product for nRF52810 which can only run SD112 and I want to...
This link source.android.com/.../services seems to indicate that L2CAP CoC is available in Android 8.x but support may vary by device vendor. Does anyone know how to verify...
Hi,
I just installed the latest NRF5 SDK - nRF5_SDK_15.0.0
and trying to run examples such as "examples\ble_peripheral\ble_app_hrs\pca10056\ser_s140_spi_5W"
But for...
We are developing a bluetooth product that operates on a battery where every uA counts and I have a couple of questions about current consumption in System On Low Power mode...
I am creating a BLE beacon scanner, using nRF51822 and SDK 12.0.0. My beacons will be using public addresses so the upper 3-bytes of device addresses of all my devises will...
Hi,
in our application we will have a main MCU and a second MCU, an nrf52832.
We need to update the fwon the nfr52832 from the main MCU using a bootloader, via UART. ...
Hello,
I want to use 2 SPI bus with nRF52832 IC and SDK5. I can use the "SPI example" for first SPI bus. For the second SPI Bus, I think that I need to modify "sdk_config...
My devices require calibration and self test to be carried out after programming. To implement this, my device checks the JLink reset pin (configured as a GPIO on my NRF52...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
