Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
nrf52832.
SDK14.2
Segger ES V3.34a
I am using nrf_drv_saadc_calibrate_offset() and find the next sample immediately after the calibration is erroneous.
There is...
Hi, I would like to use a nRF51 Dongle to connect to BLE devices and retrieve some data.
I already tried my scenario through nRF Connect for Desktop and it works, so I assume...
Hi,
I have a SPI sensor on an nRF51822, developed in mBED. To save battery power, I want to disable SPI while in ble.waitForEvent(). The only reference I could find is an...
Hi, I'm using Master Emulator API 2.1.7 and am having difficulties determining where I should be processing an acknowledge packet being returned from the slave after transmitting...
Hello,
I have been trying to have a central/peripheral device read UUIDs and RSSI values from surrounding peripherals using their advertisements and without actually connecting...
And base the nus service ,each peripheral can send message for cenrtal to other peripheral like mess.
I doubt it is possible because this example is base on the LED Button...
I'm building a smarthome application.
IPv6 over BLE not support mesh topology that is quite inconvenience to extend network. My teacher require me that this application...
I am working on custom programming of nRF52832. I have little experience of Preview DK. I took help of examples in SDK v15 and came across nrf_pwr_mgmt.h header file which...
Hi,
My service (nRF52832, peripheral, SDK14.2) works in a control point / response manner:
Command code is written by central to 'Command' char (F901). On peripheral...
Hey guys,
The project I'm working on utilizes the secure DFU bootloader and buttonless DFU.
To get the application working I had to generate a bootloader-settings file...
Hi
I have a sample nrf51822 non BLE program (based on flashwrite_example) that successfully writes and reads flash (last flash page) in a loop, incrementing the number that...
Regarding DFU upgrade, I have the following questions（sdk14.2）: 1.nrf52832 will be paired and bound after connecting with the mobile phone, then in the sdk_config.h file NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS...
Hi,
I'm working on customized light switch demo where I'm able to send string data over mesh, I'm using mesh SDK v2.0.1, I would like to have Provisioner node to be also...
Hi,
If I connect supply from laptop using micro USB cable, battery on PDK also gets discharged?
Asking this because in the initial stages of testing PDK battery is working...
Hello, I use nRF52840_SDK_Mesh, when I run the Light_Switch example with the first Client for the first nRF52840 card the 4 leds light up, and it's the same with the Server...
