I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I am currently trying to extend the range of the bluetooth mesh application. The infocentre infers that the function:
typedef struct
120 {
121 radio_tx_power_t tx_power;...
Hi,
I wonder if someone can make recommendations for types of 'smart bracelet' ('smart wristband') devices that use a BLE chip of Nordic's nRF51/nRF52 range. Can you point...
Hi,
I'm currently developing software on nrf52832. Unfortunately, I can't use the SDK for different reasons.
I'm currently looking at the RESETREAS register. If I...
I use the following code to write 32-byte to L01-module. (The wireless-communication works successfully ).
The following ( 420us+200us ), accompany only 32-byte wireless...
Hi.Is there any inbuilt ic present in nrf52840 DK board to monitor battery management ??if so, how to use that for measuring battery life?can anyone help me out plz!!
Thanks...
Good afternoon, I have a new small, but I think important, question. I did not find a concrete answer on this forum. The question concerns the correct switching of buffers...
I had try to use nRF connect to connect between nRF52840 Dongle and the bluetooth of application.
(I'm not sure the model of bluetooth of application.)
It's connected...
How many crystals/oscillators do I needfor a NRF51822 WLSCP chip?
I looked at datasheet and I'm assuming I will need a 16 Mhz crystal, a 32Mhz crystal, a 16 Mhz oscillator...
I am using IAR workbench and working with the nrf52 DK, using the S132 v.3.0 softdevice. I used the blinky example code to connect the nrf52 with my android phone over BLE...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
Hi!!
Now I am using sdk 14.0.0 / example / peripheral / spi / pca 10040 / blank / arm5_no_packs /
I am sending commands to ads 1192 with nRF 52832 DK as master and after...
I had an issue on using HID to control the media in Android. It worked fine at the first connection, I could play , pause and change the song on phone. But it couldn't control...
