Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
is it possible that there is a mistake in the infocenter documentation of SDK v.15?
In the bootloader description under MemoryLayout:
Usage
Memory range...
I have recently downloaded nRF5_SDK_15.0.0_a53641a and tried to compile and run the ble_app_hrs on the nRF52 Dev Kit. I am using IAR-EWARM v8.30.1. The Soft Device is s132_nrf52_2...
RE: nrf52840QIAA - Can you recommend circuitry necessary to switch source between the usb and LiP battery? Can you recommend inexpensive/small footprint boost circuitry to...
Hello,
I control buzzer using below API.
I want to know the maximum value of period_in_us .
Thanks.
******************************************************...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project: C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\cli\pca10056\blank\ses
I...
Hi,
I use STM32F103 as a receiver.
I read FIFO STATUS and STATUS register then execute FLUSH_RX command through SPI.
I continuously read FIFO_STATUS and STATUS registers...
Hi,
I asked previously about power efficiency for the NRF52840 SDK version V15 ( https://devzone.nordicsemi.com/f/nordic-q-a/36083/maximal-power-efficiency-in-main-loop...
I have an idea to open the source code of my personal project, since some source code of SDK are used and modified, is it OK to include the modified SDK source code in the...
I am using nrf52 developmemt kit. I am using mpu9250. the odr of mpu is 100 Hz. i am able to send data over ble using example code nrf5-ble-mpu-data-ready-interrupts . Now...
I' m using the nRF51 Dongle (PCA10031) for the evaluation of the OTA DFU bootloaders of SDK15.0.0 with the NRF52840 PDK. Using the PC tool nRFConnect V2.3.2 with the App Bluetooth...
I'm developing a product with the nRF52840 using nRF_SDK 15.0.0 and s140 v6.1.0. Since my device is not power constrained, I want to maximize the range, so I use Coded PHY...
It is stated that the advantage of a Softdevice is that because it is a precompiled binary file it can be used without requiring any particular compiler or linker features...
