Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi everbody,
I'm using the BLE Database Discovery module to discover services and characteristics of a BLE peripheral. This works fine, except for one strange quirk:
When...
Dear Nordic Support Team,
I’ve bought an evaluation kit here : http://t-yuden.com/ut/product/category/module/EYSHJNZWZ.html
and i would like to program the chip, so i...
Hi,
I am scanning from my nRF52840 and connects to one peripheral and i have written code to get it's Device information(DIS) and i stored all these information in some...
I'm having trouble maintaining a connection between my nRF52832 and Raspberry Pi. I followed the step by step guide (making sure to use the correct IOT SDK for my board),...
I am gaining my expertise in Nordic. After learning from tutorials. most of the tutorials mentions to use master control panel. But I cannot able to scan using master control...
Hi!
I am currently developing an application for nrf52832 and am using the uart module with retarget.c for output over uart via printf().
Now a few days ago I added...
Hello everyone ,
We have done advertising and scanning(both in a single firmware) on nrf51822 using QFAC chip. using SDK 12. Now we want to switch our code to NRF51822 QFAA...
hi
I am trying to add Manufacturer specific data
ble_advdata_manuf_data_t manuf_data; // Variable to hold manufacturer specific data uint8_t data[] = "A"; // Our data...
Hi, when I provisioned the client and servers via provisioner to create mesh network, I can receive RSSI value from provisionee ,but after the provisionee disconnect to power...
I have a nRF51 DK. I am trying to sniff the Bluetooth connection between the smartphone and watch at Window 7.
Installed:
Wireshark 1.10.7
Sniffer (tried ble-sniffer_nRF51822_1...
The sdk_config.h configuration file for ble_app_hrs_freertos example contains following definition:
#define NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS 1
This macro should...
HI,
I have connected to one peripheral from my central and retrieved all the services(For example i need Device Information Service, got all the characteristic values) and...
dear sir,
i have a nRF52DK board,
i want to power on the board but not glowing LED and my laptop not detect the board while connect with laptop,
please given solution...
Hi
Env: keil and no SD
I am doing the first steps on keil + nordic nrf51822. I started by opening the Blinky app (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples...
Hi there ,
i am developing a biomedical recorder which needs to continuously transmit the recorded data ,
data rate is very low (9.6 Kbit/s to 32Kbit/s) but i have a very...
