Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
I'm trying to port my application from the nrf52832 to the nrf52810. I'm using the Fanstel modules, originally was using BT832 and am now trying to bring the application...
1.What are the dimensions of the NFC antenna (component A1) for the reference designs given in the design files here
http://infocenter.nordicsemi.com/pdf/nRF52832-CIAA_Ref_Layout_v1...
Hi,
As showed in the code, I masked " else if (m_nw_state.provisioned_devices == 0) ", then it reported "NRF_ERROR_NOT_SUPPORTED".
Can you tell me how should I do...
Hello,
I didn't manage to run PA/LNA switching with softdevice (function: sd_ble_opt_set(BLE_COMMON_OPT_PA_LNA, &options)) with P1.* GPIO pins.
Note that all P0.* pins...
Hi,
Is there any chance that we can completely turn-off the radio part of nRF52832 and only the application part of the processor running. Also, we should be able to turn...
Hi,
I would like to program and debug a code into the Nordic Thingy:52. I read that I should have either J-Link or nRF52 DK. And I have the nRF52 DK, but I don't know...
Hello all,
I'm working with the nRF51 SoCs, with the s130 SoftDevice and SDK12.1.0
I have a BLE Nano from Red Bear Lab that has a nRF51822 doing adv and it expose...
I want to put application, softdevice, and bootloader into one hex file, after doing research, I think I need bootloader settings page to make the application run. I get the...
Hello,
I have been using another vendors mesh stack to develop a product that uses mesh networking, however, their stack is limited to storing provisioning data in a certain...
I'm trying to set up DFU for a custom board with a nRF52810 module (Rigado BMD-330). I created the secure bootloader from the recent project for SDK 15 posted by Vidar Berg...
Hello!
The NRF52832 uses the QFN-48 form factor but I'm having some problems finding it in Fritzing. Did some made their own, know where I can find it? Fritzing has QFN...
Hello,
I'm using SDK15.0.0, device nRF52832 and softdevice S132.
After open "secure_bootloader_ble_s132_pca10040_debug-nrf52832_xxaa_s132" project and build it, I got...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
When initializing a UART instance (0 or 1 or both together), the current consumption increases to 600 μA
Then deinitialized UART, but consumption is not reduced!
- I tried...
Hello everyone!
I've had an ESB application running o the nRF52832 for more than a year. When I moved it onto the nRF52840 it no longer works. There are no changes to the...
