Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I face a problem when trying to perform a DFU firmware update via command line using nrfutil dfu ble.
I'm using windows 10 and nrfutil.exe version 3.5.0
I am using...
Hi,
In application note 'nWP017 - Antenna tuning', it provides quite a lot information about how to tune antenna.
But, once it is properly tuned, how do I know the matching...
Hi,
When I do not call advertising_start(erase_bonds); then I only draw about 2uA.
When I call advertising_start(erase_bonds); I draw 350uA.
I want to advertise. Then...
Hello Nordic Team,
I have few analog sensors that operate at 5V DC and outputs voltage signal within 0.5V - 4.5V range. I know i cannot interface these sensors with nrf52832...
Hi,
I am working on a project with nRF24L01P. Recently I was trying to make nRF24L01P to transmit packet continuously and i have configure the chip in no_ack, TX and shockburst...
I am using nrf52832 based on SDK14.2 development. I used the air upgrade method in the routine "buttonless dfu". After the online upgrade is successful, nrf52832 will be automatically...
Hi,
we have a nrf51 mounted inside an AC motor housing which we assume is causing an unintended flash erase from time to time (checked with nrfjprog --readcode).
Is...
Hi,
We have a custom board with a Telit Bluetooth module, Bluemod+s42, now.
At present, I am using the "nRF Mesh" APP to test the feature of proxy. But, I encountered...
https://devzone.nordicsemi.com/f/nordic-q-a/29255/mtu-size-of-nrf52832-as-central has the answer of how to change MTU size. Could you please provide more details with the...
Hello,
We have bought two EVAL boards, nRF52840-DK, in order to try our goal to add to our already working projects BLE option. This happened about two weeks ago, and since...
Hi,
I use S130 with SDK 12.3.0.
I have an application that permanently advertise with an interval of 10s but when the user push a button I switch to BLE_ADV_EVT_FAST ...
all the details needed to reproduce my situation, including:
development software, with versions soft device s110, nrf51822
Computer platform, with versions (Windows)
...
I am calculating the worst case current consumption of the nRF52832 SOC.
Could you please help to get the current consumption data of the nRF52 i.e. at -40 deg C and 85...
Hi. I'm using nRF52832, SDK13.0.0.
I made my code as below.
char_md.char_props.notify = 1; char_md.char_props.read= 1; char_md.char_props.write= 1; // char_md.char_props...
