Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi Support team,
In this application note, solder paste type 4 has 25 to 45 micron particle size range while IPC J-STD-005 as attached stated type 4 has 80% Minimum between...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
Hi! I'm developing on nRF51 with SDK 11 and trying to extend our application with buttonless BLE DFU support. Due to limited flash memory, we could only use single bank ble...
The website is broken for me, and I see a sequence of orange pop-up messages saying "An error occurred. Please try again or contact your administrator."
When I use master control panel to scan ibeacn, I find "Complete Local Name" in below picture,
How to set the "Complete local name" ?
I heard someone says set in the...
Hello,
I've now been looking for a while but haven't yet found anything working to programmatically unwind the call stack when working with the nRF51 or nRF52.
Basically...
We are completing the design of a PCB and have a mounting/assembly issue with the NRF52840. We In looking at the mechanical spec on your datasheet w find that A row of 24...
hi
1.does nRF5-SDK-for-Mesh v 2 support friend feature of Bluetooth?
2.phone with ble 4 can current to ble 5 mesh network?
3.is there any example of two above?
thanks...
I have connecting problem.
My setting...
1. OS : win10 x64
emulator : J-link(EDU)
2. installed
1) nRF5x-Command-Line-Tools_9_7_3_Installer.exe
2) nrfgostudio_win...
Hello
The scanner causes the code to freeze when a debugger is not connected.
We are developing a system where one of our units is to run on the nRF52832. During development...
Hi ,
I testing the " nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c " sample code with nRF52832 . Found sometimes get the advertising...
We are using nRF52840 with the nrf5_SDK_for_Mesh_v1.0.0 in combination with s140_5.0.0-3.alpha I'm working with the nRF52840-Preview-DK board. Task: program a bootloader for...
Hi, developers !
We are going to make a USB dongle that configures RF HID using nrf52840.
So when I look at the datasheet for circuit configuration, it says "High voltage...
Hello, I want to transmit data using the nRF52840 card and a smartphone. I explain: I must transmit data from the nRF52840 card to a smartphone. What is the best program in...
