Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I have a compile problem in esb_ptx of SDK 11.0.0.
When I add a esb command "nrf_esb_rf_channel_get()" in nRF5_SDK_11.0.0_89a8197\examples\proprietary_rf\esb_ptx\main...
Hello everyone, I would like to change the name of my device with sd_ble_gap_device_name_set (). But the resulted name in the nRF Connect app is always "N/A". Here's my code...
How do I change the name of the USB device? I am starting with the USB Audio Demo and, logically, it shows up in Windows as "nRF52 USB Audio Demo" but I cannot find that text...
I am a beginner to Nordic devices and to Bluetooth technology in general. I have set up a Bluetooth connection using the nRF51 Development Kit and an nRF51-Dongle. The dongle...
Hello
In our production facility I need to read and write NFC NDEF messages to a NRF52832.
Is there any recommendation for a working and easy solution with an USB NFC...
Hi all,
I try to create a new project to update my firmware using twi(I2C) interface.
In my test case, first i download firmware to region2 via keil, then copy the firmware...
Hi Nordic developers,
For my internship I’m developing a BLE application on de NINA-B111 module which does have the nRF52832. I'm using SDK 15.0.0 and Softdevice 132 v6...
We're disabling pending FPU exceptions and clearing pending FPU IRQs before calling sd_app_evt_wait(), as per a few references:
https://infocenter.nordicsemi.com/index.jsp...
Dear NordicSemi engineer:
I want to connect to a peripheral device using a modified ble_app_uart_c.The information of the peripheral device is below:
How can I connect...
I need to allow BLE connections for a period of time after restart, then prevent connections (unless a button is pressed). Is this functionality as simple as re-configuring...
Hello,
I am currently developing software that scanning ble advertisement packets without pairing and advertise them like beacon. I used examples which are ble_app_hrs_c...
Hi!
I'm working on HID mouse example on SDK 13.0.0, SoftDevice S1332 v4.0.5. I'm supposed to use this as a low power media button control, using a nRF52 DK. I've done a...
Hello,
We wish to use nRF52832 IC in our design. We will design an equipment which can connect to another device via BLE and can send some measurement data. Our equipment...
Hey everyone,
I'm working with nRF52810 . I want to write into UCIRs before program execution starts.
I tried to configure NVMC(Non Volatile Memory Controller) and then...
I am using the nrf905 in a project. The datasheet suggests crystals of 4mhz, 8mhz, 12mhz, 16mhz and 20mhz are all acceptable. Does the choice of crystal oscillator frequency...
