Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi, I have been developing on the nRF52832. I am now in the process of moving to the nRF52810.
I am using the SDK v15.
I have commented out the DEVELOP_IN_NRF52832 define...
The last warning log i had was
E 14:06:57.204 Error 129 (0x81): GATT INTERNAL ERROR D 14:06:57.229 [Server callback] Connection state changed with status: 0 and new state...
Hi Sir
How to config channel and AINx to specific gpio for SAADC ?
For example, if I want read adc voltage from NRF_GPIO_PIN_MAP(0,5), how to set the channel and AIN ...
Hi ,
SDK : nRF5_SDK_15.0.0_a53641a
Chip : nFR52810 【1】Is nRF52810 only use pca10040e （nRF52832 = pca10040 , nRF52840 = pca10056） ? And can't use wrong （nRF52810 use pca10040...
Hello, Nordic
I have to immigrate from SDK14.2 to SDK15. I know that many things have changed in the process.
I'm referring to the Immigration guide but, There is UART...
I am using a PPI to implement a READY line for my SPI slave.
PPI's EEP is set to my SPI slave's EVENT_END
PPI's TEP is set to my GPIOTE's TASK_SET to deassert my READY_n...
Hello,
My previous question is this.
I try to implement sample application with Radio Driver 1.1.0 to SDK15.0.0 ble peripheral uart example.
Symptom
For few micro...
Hi:
I am fairly new to Nordic so please excuse my ignorance. I recently took over a project which used sdk 11 and I am in the process of updating it to 15 and want to see...
Hello,
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery. We need to measure current profile for the beacon and calculate corresponding...
My environment is:
SDK14.1 + SD132 V5.0 + NRF52832
2 sensors(MPU9250 + LPS22HB) 1 battery gas meter (LTC2942) are mounted on TWI ( +1mA)
SPI to spi flash. (+1mA) and...
Hi，
I use SDK is nRF5_SDK_15.0.0_a53641a
【1】In examples proprietary_rf , Here is only the example of pca10040 , So I have to download a lower version of the SDK ?
（...
Hello, I am trying to setup and use the nRF sniffer (ble-sniffer_win_1.0.1) on my NRF51DK (PCA10028) board. I followed the instructions and using nRF studio, I erased all...
Hello!
I'm currently trying to lessen the current consumption of the nrf8001.
I tried to change the connection interval, slave latency, and the timeout using ChangeTimingRequest...
Hi,
I've been using the nRF24l01+ for some time now and am quite satisfied. I'm having a new issue that I'm unable to explain and for which I would greatly appreciate some...
I have filed an issue related to HCI UART sample from zephyr running on nrf52832. I compiled the hci_uart sample successfully, but I am not able to use the UART interface...
