Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi, I'm kind of a newbie, haven't had much experience with embedded outside of arduinos etc.
So I started to look at this: https://learn.sparkfun.com/tutorials/nrf52832...
for sdk15.0, SES,
is the twi_scanner example known to work with nrf52810?
getting errors,
undefined reference to nrfx_twim_init, nrfx_twim_enable, nrfx_twim_xfer
Hi,
I am studying the GPIOTE example from SDK 14. I did some modification adding other led and doing the leds blinking in differents times (LED1 blink each 1 sec and LED2...
Hi,
The nRF52832 does not support Long Range and i was wondering if the use of "RADIO_MODE_NRF_250KBIT" would increase the range. My application is a mesh network.
Do...
Hello Everyone,
I am using nrf51822 with S130.
Currently I am using arduino following this repo to program nrf51822 and its working fine. However, I want to shift to keil...
Hi there
For test purposes, I first implemented a simple serial reading & parsing function in polling mode of a gps device (sending @ 1 Hz).
Everything works fine when...
Hello,
i am evaluating the nRF52840 on the nRF52840-Preview-DK. I have connected an ADC to the devkit via SPI and my code reads data from the ADC via GPIOTE, PPI and SPIM...
We've got two SPI slaves that we need to talk to with the 52840 (PCA10056 dev kit for now) using SPI Manager. In the initialization of these devices, I'd like to use nrf_spi_mngr_perform...
when I use flash to storage my data,I call the fds_record_write(&record_desc, &record) ,and it return success,but my machine run err, my ble broadcast is missed.I used the...
I'm trying to understand what is meant in section 5 of the BLE on Android primer: "The peripheral device should disconnect itself when it gets disconnected by the client....
Hellou, I am developing application which need data array store to flash manager. I used for some function for storing data (nrf_fstorage_init(), nrf_fstorage_erase(), nrf_fstorage_write...
Hi!
I'm trying to merge the flash_fds example with the ble_app_uart, and the twi example. My intention is to read a value from TWI, store it in flash and then send the...
Hello,
I would like to know how can I configure the parameter NRF_SDH_BLE_GAP_EVENT_LENGTH for a determined NRF_SDH_BLE_GATT_MAX_MTU_SIZE when enabling data extension. ...
hi team,
i was using nrf52840 with sd 5.0 and developed a custom application using ble_app_proximity in 14.1. my use case is my device should hand shake only with my mobile...
In the NRF_SDK_15, only 3 drivers (clock, power, rng) use the return value NRFX_ERROR_ALREADY_INITIALIZED. Why are the others drivers initialization return NRFX_ERROR_INVALID_STATE...
