Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello,
I want to get the raw acceleration of the Thingy 52. however I can't understand the values I get from the raw acceleration. What is the unit used for raw acceleration...
I am using Nordic SDK 13.0.0 with PCA 10040 dev board.
I have configured the stack to use MAX_BLE_MTU_SIZE = 200
// Configure maximum size of ATT packet the SoftDevice...
Hi,
I encountered a weird behavior. i defined characteristics with specific read/write permission however all the characteristics are writable for some reason altough the...
Given this error handler function...
and this logging from it with the Segger attached...
how do I debug this?
I presume the info passed in is bogus and just points...
Hi All,
I'm currently using SDK12 for nRF52832. In my BLE peripheral project I store central address who engaged my device to listen for ANCS notifications. This address...
Dear Nordic Community,
I am using the the nrf51 dev kit to try and program a custom board (nrf51822) connected to it via the the Debug Out connector. This setup has worked...
Hi,
I'm testing nRF52832 central data rate.
My SDK version is 14.0.0 and softdevice is 5.0.0.
I want to send 200byte from nRF52832 peripheral to nRF52832 central in one...
Hi,
I'm using NRF52840 with Softdevice and SDK v15. I would like to use an external 32.768kHz crystal.
If I understand correctly this is consistent with the eval board...
Would you please provide an example of using PA/LNA with nRF52840 (Softdevice S140) on SDK 15.0 or higher?
Unfortunately, I could't manage the code you've provided for the...
Hi With regards to iOS and Android versions of the 'nRF Mesh' applications .. (1) How can I tell if both apps are 'synced' to the same level of functionality/user interface...
Hi,
I want to test UART peripheral on nrf52840 by running example in path examples\peripheral\uart as it is.
Connection setup is:
nRF power source USB
nRF USB port...
Hi all
Previously, I used the nRF52832 with the interrupt-driven UART at 1Mbaud. But due to SoftDevice interrupts that blocked the UART-RX-IRQ for more than 6 bytes, I tried...
I am trying to set up fifo'ed uart. However, APP_UART_FIFO_INIT crashes with an error value 8. I traked back the reason into this nrf driver code fragment:
ret_code_t nrf_drv_uart_init...
