Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
My app was written on Windows PC/MSVC and is ported to nRF52/Keil.
In many places I've used MSVC assert() macro in the following manners:
assert(function(arg1...
Hi all,
On SDK 15.0, Immediate Alert Service is not working without a secured BLE link. When peripheral is not paired, this latter doesn't receive any alert from central...
I’m using SDK 15.0.0. and softdevice 6.0.0.
When I compile the example:
https://github.com/haakonsh/MMD
I get the compiler error:
fatal error: compiler_abstraction...
Hi,
I tried ble_app_uart example by using SES it works fine. Then I tried it by using eclipse with OpenOCD and a STlink V2 on the debug in port I succeeded to flash it....
Hey guys,
With the new SDK15, I find myself looking at dependency problems over and over again. Right now, I am trying to setup a simple A/D conversion using nrfx_adc. Found...
Hi Env: keil uvision 5 and SDK 9 and custome breakoutboard for nRF51822 (PTR5518: no external crystal) and no SD.
I am trying doing the first steps in twi over nRF51822...
I been reading over your entire tutorials, but I have yet to see any tutorials that guides me towards creating an NRF52 project from scratch? Could anyone guide me through...
Hi,
I am transferring my nrf52832 project to nrf52810,and I have deploy the project according to the user guide (Transferring the project to nRF52810 hardware),
when I...
Hello everyone,
I'm developing an application for boards with NRF52832, Softdevice S132 3.00 and SDK 12.3.0.
The network architecture consists of:
one peripheral board...
I'm using my accelerometer's GPIO interrupt to wake up the MPU from PowerOFF mode and it works great. Now, I'm trying to use the same interrupts to wake it up from Sleep mode...
Hi,
I have migrated from SDK14.1 to SDK15.
One thing is embarrassing me.
I would like to modify the scan data as above, I do not know where I can fix it.
phy...
Hi,
I am using mbedos for a NRF42832 and am currently in the situation that I have to profile my code with gprof. Here comes the issue: the Nordic SDK uses explicit assembler...
this picture is from infocenter.nordicsemi.com/index.jsp
and this picture is from 《S132_SDS_v5.0.pdf》
in first picture the application base is 0x00020000 , in...
I've been instrumenting my Nordic app with RTT logging, which has been working great up until now. I use the deferred mode and use nrf_log_push() to queue all dynamic strings...
For the connection event collision, I have some doubts, I hope to get help in devzone
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.s132.sds...
