hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Dear,
I see the Uart Rx packet loss at higher badurate, ie 460800, 921500, 1M.
I use NRF52, SDk15 with softdevice 6.0.
UART TX is no problem, but there is loss of RX...
Hi,
I am using a 24L01+(as PTX) communicating with a nrf52832(as PRX).
I can have these two device communicating, where nrf52832 can receive data from 24L01+.
However...
I am using SDK 15 and i have successfully flash soft device , boot-loader and application code using nrfgo studio. Connecting using nrf connect application. Click on the DFU...
Hi,
We are transitioning a product from the nRF51 to nRF52832, and I am looking into what I need to do to get our code ported over and approved with the Bluetooth SiG. ...
Hi there,
I am a using a nRF52/SDK 13 to communicate to an external board which uses AT commands, I would like to save some battery during the time I perform my AT command...
I read that the old SDK for mesh had the provisioner and client as the same operation, as I am trying to make my own philips hue style wireless lamp I would need to get my...
Hi!
My question is for the purpose of power calculations for both the nRF52832 and nRF52840 for BLE use only.
I haven't been able to find a reference for this.
I see...
I'm trying to follow "Bluetooth low energy Advertising, a beginner's tutorial" by MartinBL found at https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble...
Hi, in my previous attempt to fix n52DK, I fixed the n52DK board's power rail. It turns out not the problem of the interface MCU shorting VDD.
But when I followed the instruction...
Hi All,
Just feedback from Lab, they said that they can set any channel frequencies at bandwidth = 1MHz in the Direct Test Mode. BUT they said that they need to test any...
Did someone try to make QT application that supports DFU for BLE devices? Can it be done using nordic DFU android/ios libraries (to include them somehow in QT project)?
Hi,
I am having a problems with USB enumerating with a custom board based on the nRF52840. The board is self powered by LiPo battery. I am developing by connecting to the...
Greetings,
I'm attempting to use the ble_connectivity example for the PCA10040 and have a couple questions:
1) What are the default GPIO pins for UART?, for SPI?
2)...
