I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I wanted to know if this program starts sending advertisements using the Coded PHY OR if it starts advertising in the normal advertising channels using the normal 1Meg output...
Hello, I want to build serial_lte_modem sample for a custom board based on nRF9151, but it fails with this error:
error: Aborting due to Kconfig warnings
I can build...
Dear,
I recently upgraded my project from NCS 2.4.0 to NCS 2.9.0 and encountered an issue with the ST7789V display driver.
Previously, I used SPI0 to interface with the...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
Hi there, I´m totally new to Zephyr & Nordic, started with some Trainings on NRF52840DK and jumped in with a device driver developement where I took a availalbe out of Tree...
Hi All,
I have a question and slight confusion as referring to couple of links.
Performing KMU provisioning : Here we are highlighting provisioning of private key up...
Environment info:
Tested on own integrated product, and nRF5340 Audio DK.
Firmware built on Fedora Linux 42,
Using the Rust programming language, using embassy-nrf &...
Hello,
I am working on a prototype board based on the nRF7002 DK. I have managed to preserve the entire PCB layout sections for the nRF5340 and nRF7002 radios and antenna...
Dear Nordic team,
We are currently preparing for Wi-Fi, BLE, and LTE compliance testing scheduled for next Tuesday, and are encountering a blocking issue with the Radio...
I've been using the power profiler 2 kit for a couple of years and everything has been working fine - a few days ago I was promoted to do a firmware and version update (which...
Hi Support Team
Our project needs to support the following features: 1 BLE central role, 1 BLE peripheral role 1 PWM, 1 UART, 1 ADC OTA and BLE bonding
Can the nRF54L15...
Hi,
We are developing the module based on nRF54L15 with nRF21540.nRF54L15 working fine now nRF21540 not functioning.
We have also verify with to connect nRF54L15 DK with...
Hi , Support
Since I only have one development board each for Nrf52840DK and NRF54L15, I would like to know whether Distance Measurement with Bluetooth LE discovery can...
Hi Nordic Team,
am I currently evaluating the nrf5340 development kit for our new product revision and fail to get a power efficient shell besides rtt logigng.
Concrete...
Hello,
I'm getting the below mentioned error when I try to build Light Bulb sample with MoveToClosestFrequency in LevelControlCluster .
/home/dotdll/ncs/toolchains/7cbc0036f4...
