I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I would like to use PPI in order to set out pin and start a timer at the same time, from software.
I cant find a way to create an event from software that will fork a START...
Hello everyone, I'm currently writing my bachelor Thesis and need to establish an iot (preferably mqtt) connection from my pca10028 with my PC as broker (i.e. with mosquitto...
Why is AAR blocked if the Peer Manager Library (e.g. SDK12.3 see id_manager.c) uses the -softdevice SoC API- function call sd_ecb_block_encrypt() to resolve RPAs (Resolvable...
I am trying to connect to 8 slaves/peripheral with a single central/master connection but i wan to understand that how the connection us managed between the multiple slaves...
Hi;
I using experimental_ble_app_buttonless_dfu as the project. After build the project and download with softwareDevice , it works ok . Then I compile bootloader_secure...
Hi
I have done setup using guide ( https://github.com/sandeepmistry/arduino-nRF5 ) by sandeepmistery.
I am able to blink led of nrf52DK using Arduino example code. ...
When i choosing among the 52832 and 52840, i found this table.
One point i am not sure, i believe the 52832 stack is already support Bluetooth 5, but why the table said...
Hello,
I would like to manage time (hours, minutes, seconds) on NRF52 chip: what is the best way to do it ? How to use as less energy as possible ?
At the first connection...
Hi all,
I'm new to Bluetooth technology and just start some test for indoor localization using 52382. But I find out that 52382 does not support the long range feature of...
Hello all,
I'm curious if anyone could lend some thoughts.
I'm just in the research stage and going through a few examples but getting a little overwhelmed.
I'm trying...
Hi,
I am using nRF51822, S130, SDK 12.3.0
Want to use is low power failure warning. using the following code.
However, when break on line err_code = sd_power_pof_enable...
I am currently using a CSR 4.0 dongle 8510 A10 chip on Windows 10 Creators update
I can get it to Pair with the nRF52832 in windows, according to windows.
I have a ...
I am upgrading an existing project that was working on SDK 14.2.0 with S132 5.1.0 to SDK 15.0.0 with S132 6.0.0. I'm using IAR 8.20.1, and have made the changes suggested...
