I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
I was hoping someone could clarify what support the nRF52840 has for USB power source detection. Our design uses a 150mAh LiPo battery, with a dedicated PMIC. We have the...
I have a hardware with NRF52832 module and successfully used the example twi-scanner to locate my I2C peripheral. I copied these parts over:
My own code produces this...
I am extending the Glucose sensor app in nRF Toolbox (Develop thread). I had logic error which I have corrected, but while debugging I encountered a strange effect that could...
Hi, I have been developing on the nRF52832. I am now in the process of moving to the nRF52810.
I am using the SDK v15.
I have commented out the DEVELOP_IN_NRF52832 define...
The last warning log i had was
E 14:06:57.204 Error 129 (0x81): GATT INTERNAL ERROR D 14:06:57.229 [Server callback] Connection state changed with status: 0 and new state...
Hi Sir
How to config channel and AINx to specific gpio for SAADC ?
For example, if I want read adc voltage from NRF_GPIO_PIN_MAP(0,5), how to set the channel and AIN ...
Hi ,
SDK : nRF5_SDK_15.0.0_a53641a
Chip : nFR52810 【1】Is nRF52810 only use pca10040e （nRF52832 = pca10040 , nRF52840 = pca10056） ? And can't use wrong （nRF52810 use pca10040...
Hello, Nordic
I have to immigrate from SDK14.2 to SDK15. I know that many things have changed in the process.
I'm referring to the Immigration guide but, There is UART...
I am using a PPI to implement a READY line for my SPI slave.
PPI's EEP is set to my SPI slave's EVENT_END
PPI's TEP is set to my GPIOTE's TASK_SET to deassert my READY_n...
Hello,
My previous question is this.
I try to implement sample application with Radio Driver 1.1.0 to SDK15.0.0 ble peripheral uart example.
Symptom
For few micro...
Hi:
I am fairly new to Nordic so please excuse my ignorance. I recently took over a project which used sdk 11 and I am in the process of updating it to 15 and want to see...
Hello,
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery. We need to measure current profile for the beacon and calculate corresponding...
My environment is:
SDK14.1 + SD132 V5.0 + NRF52832
2 sensors(MPU9250 + LPS22HB) 1 battery gas meter (LTC2942) are mounted on TWI ( +1mA)
SPI to spi flash. (+1mA) and...
Hi，
I use SDK is nRF5_SDK_15.0.0_a53641a
【1】In examples proprietary_rf , Here is only the example of pca10040 , So I have to download a lower version of the SDK ?
（...
Hello, I am trying to setup and use the nRF sniffer (ble-sniffer_win_1.0.1) on my NRF51DK (PCA10028) board. I followed the instructions and using nRF studio, I erased all...
