Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
Hi Nordic team,
This is a compatibility test. case1 okay: 1,Connect the nRF5340BIS headset with the phone. 2,NRF5340 broadcast can be found on the mobile phone. 3,When you...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
I've seen a few posts about this, but they are all old, and maybe don't apply to USB-C We have a device that already uses USB-C for battery charging. We want to carry the...
Hello I have a custom board with the following dts My zephyr app crashes in bt_enable() Note that uart0 TX pin 8 is used by gps_vrtc_en but uart0 is not defined. Same crash...
Hi
I have been using my out of tree driver for my BG95 module, which I have copy pasted from the zephyr's quectel_bg9x driver (drivers/modem/quectel-bg9x) and its required...
Today I opened VS Code to find all my Zephyr/NRF #includes have the red squiggly lines with an error such as "cannot open source file zephyr/types.h". Right click -> Go to...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
I found this in nRF5_SDK_17.0.2_d674dde/components/libraries/memobj/nrf_memobj.h :
/ ** * A memory object can consist of multiple chunks with the same size. Each object...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
Hi,
I found that the NRF 54l15 can only estimate distance based on channel sounding and RSSI. On the bluetooth website it mentioned channel sounding accuracy being around...
