Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
NAND or NOR flash memory to use with nrf25832? my application is to store the data from mpu-9255 to flash memory. my data rate is about 3 mega byte per hour and i have such...
Hi,
I am using Linux ubuntu 14.04 with kernel version 4.15.0-041500-generic for 6lowpan over BLE and MQTT broker wit IPv6 address as inet6 address in below image
In...
If I use DeveloperStudio_1_1_3139_0 to generate a profiles and services for the latest SDK 15.x, will it correctly work?
I recall back with SDK 11/13.xx it was not compatible...
I need to sample ADC channel at the fastest deterministic rate.
If i use burst mode with 3us acquisition time, do i get a sample exactly every 5us?
does t(conv) is always...
About example BLE_uart,
My device must always remain in advertising, I'm using a 1280 ms between two advertisng event.
I have to minimize the consumption during advertining...
I have a few questions about the NRF6707 Power Profiler kit and I would like to ask you: 1. The NRF6707 Power Profiler kit and nrf52 DK are linked through the ARDUIND D0 pins...
I am updating the application software that was created based on ble_app_multilink_central in SDK 9.0 to 12.3. When replacing device manager with peer manager, I received...
I'm just getting started with the Nordic chips so I will apologise now if I have failed to find my own answer amongst all the devzone content.
I want to use the NUS service...
Dear all,
I have a problem with secure connection between Android (nRF Connect) and my custom board with nRF52832. I'm usind SDK 14.2 and SD_132 v.5.0. I'm using secure...
Hi All,
Anyone know the aggregator example can run on the nrf52 PCA10040 DK?
https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role I fail to compile the...
I've got a bit of an issue with turning off specific debug statements. If I try and adjust the log level, I get a run time failure. If I try and comment out the specific debug...
I have changed the RAM (rwx) : ORIGIN = 0x20001fe8, LENGTH = 0x2018 in ble_app_buttonless_gcc_nrf51.ld. Build, it appears to me /usr/local/gcc-arm-none-eabi-4_9-2015q3/bin...
Hi to all,
i have an example that it implemented a device with some charactristics, when i use sniffer to sniff these packets i can not see the packets data because the...
I am experimenting with the mesh light-switch example. I want to control two LEDs on a single node using the SimpleOnOff model. I know I should add a separate element and...
Hello,
please help to grasp the problem,
when using the timer to control gpio pin with constant period as shown below, if trying to do advertising for BLE communication...
