Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi nordic
I'm developing using nrf52832
This board has many example code so I'm developing smoothly
but Today I had problem. It is about check time
I want to check...
Hello, I use light switch example (nrf52832, mesh sdk 2.0.1)
Can I create mesh network without servers? (clients will send messages to each other and process them)
And...
Hi, I want to use 2 I2C instances and 2 SPI instance during setup, and later switch to 1 I2C instance and 3 SPI instance. To do this, I tried to swap TWIM2 instance to SPIM2...
I'm looking to build a product which require an Android board with relay and BLE 5. I am very new to this and so far I have been playing with Raspberry Pi where the BLE and...
Hello, this will be a bit of a long-winded explanation but here goes: I'm building an SPI driver that reads data from an external ADC and writes to a PWM signal. I got the...
I figured that I could put
#define TX_POWER_PHIL +8 /** -40,-20,-16,-12,-8,-4,0,+2,+3,+4,+5,+6,+7,+8 phil **/
and then make two changes to
static void advertising_init...
Is any GPIO, as output, logic level on nRF52832 maintained when the device is in OFF mode? Same question when the system is in ON/Low power mode Thank you
Hi guys!
I am making an application that uses the PCA10056 for 2.4Ghz RF communication using Enhenced shock burst(esb).
Also, when upgrading the application, i try to...
Hi all. I fell into despair in an attempt to find a solution. If I do not use sprintf then everything works fine.
Before calling some_f, mqtt_put works without any grudges...
Function softdevice_enable() doesn't return any adjusted warnings in case of changing central/peripheral connections, e.g. my ble_stack_init() function:
static void ble_stack_init...
Hello, nordic.
I studing nfc example for oob pairing.
So, I have to intergrate to uart example and hrs nfc example.
I had intergrated uart function in hrs_nfc example...
I am trying to decide whether to use free-rtos or bare-metal.
In the documentation for the nRF SDK v15.0.0 i see that free-rtos is not supported for the nRF52840.
However...
SDK14.2
A little background on this question.
I am creating a library where I need to add items to a queue and then process those items from the queue. I would like to...
PLEASE revise the page Getting-started-with-the-rRF52-Development-Kit to include
"confirm that the nRF52 DK has appeared as a removable drive named "JLINK"...
If drive...
