Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Hi,
Sorry for post here again but i'm having a lot of trumble. I'm actually at the step 4 of the guide, which is the page generation.
I've made correctly all the previus...
I am working on a nrf51822 board and trying to run ble_app_hrs project using nrf sdk 12.1 and s130 softdevice. I converted the uVision project to the Segger Project using...
I use SDK 12.3.0 with IAR
If there is an option to know the last page that programmed?
For example:
Linker: ROM start address 0x1F000 end address 0x76fff
But...
Yesterday, I upload the thingy sdk v2.1.0 in keil uVision5 and rebuild it. After rebuild, it showed one error namely "fatal error" due to the large size(122kb). please suggest...
I am using sdk 14.2.0.I am trying to connect mpu9250 with nrf52832 dev board. whenever I took data serially on putty it is true...but whenever I try to connect it with NRF...
Hi,
I'm new to Segger Embedded Studio developmemt. And now I met a problem similar to Placing data at a specific memory address with Segger Embedded Studio .
I need to...
Hello,
We're creating a program that advertises and reads scan requests RSSI values to determine distance of central device and display them using the onboard leds(1-4)...
We are currently evaluating use of NFC on a nRF52840 which should get powered via VDDH.
Section 7.3 of the data sheet states that NFC can be used in any power configurations...
Hi Nordic engineers,
I found a strange problem that NRF52840 voltage of io high level is just about 2.65v~2.71v. I am sure that the voltage mode is normal voltage mode...
Hello,
I'm attempting to solve some issues with my BMD-200 (nrf51822) not getting the SD BLE_GAP_EVT_DISCONNECTED message. I currently Don't seem to be getting this message...
Hi, I'm not able to find the memory layout of the nRF52840 without the SoftDevice. I'm working with the nRF52840-Preview-DK and the SDK v15.0.0. I don't need the SoftDevice...
Hi sir,
we use nRF 52832 with ESB protocol. and we use ACK to send payload to PTX , but we found must use the same pipe which PTX used pipe to send ACK .
so , I have two...
Hi, Okay I got my nRF52840 Dongle, plugged it in to my window 10, verified it shows up as USB device on window's Device Manger.
Checked and Red pulsating LED (LD2) was pulsing...
SDK : 15.0
Softdevice : 6.0
DK : NRF52_DK
Hi everyone,
Does anyone have a BLE example with C ++ ? (a beacon example or anything else) I would like to have the Makefile...
Hello everone,
I'm currently seeing about 10-11 uA additional IDLE current when the SPIS peripheral is enabled, but unused. In the nRF5 SDK v15.0.0, the SPIS example draws...
