Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
The nRF Mesh Connect software available from this blog post is probably corrupted. I am not able to use it. Is there a repository for software tools where I could download...
Hi,
I am using sdk 12 with s132 v3 on nrf52832 dev board. I am running the example code for ble hid peripheral for keyboard compiled using gcc and eclipse. The example code...
Hi,Sir:
I am developing a 52840’s project using SDK15.1,My development environment is Segger embedded (version 3.34a).When I added the RNG function to the code (the correct...
Hi,
Have an issue with a prototype 2 layer 52840 pcb that i tried to get manufactured. i increased the pad diameter to 0.3mm and now i cannot route without hitting clearance...
Hi
when trying https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library everything goes OK (I think...) all the nodes gets provisioned, all the elements gets addresses...
I know the PDK design is available for download, but there are a lot of things on that board which would not be required for a minimal e.g. beacon design
I'm looking for...
We are looking at developing a proprietary protocol using the nRF52832/40 and were interested in the specific and practical differences between the Ble_2Mbit vs Nrf_2Mbit...
We try to implement DFU over UART. The Mesh DFU example has been taken as a reference. DFU is successful, but it takes about 1 hour (sic!) to transfer DFU ZIP package of size...
Hi,
We are developing a device which should have a power save mode where no BLE connection is possible (switch off the BLE to a minimum power consumption) and restart the...
Hi, there~~ Just noticed that there are codes for the Android nRF connect.
github.com/.../Android-nRF-Connect
Using that code, I wish to create my personal sniffer that...
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
Hi,Support Team
I Use the nRF51822 SOC for SDK12.3-example-DFU-bootloader_secure, when I Select the ZIP upadate file,it has a reminder "Loading file has failed. Try different...
