Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi everyone!
My question is for engineers of Nordic. I need to apply NRF52840 as a " beacon ". As there is no ready templates of beacons in nRF5_SDK_13.0.0-1alpha_055eef3...
How to select nrf528332 UART clock source, how to make the serial port baud rate not change with temperature?When the baud rate is 9,600, the baud rate varies greatly with...
i have a problem with ble_nus_send_string function, the BLE_NUS_MAX_DATA_LEN is 20 bytes but i need to send 1kb every second, is that possible? i tried to put ble_nus_send_string...
Hello Nordic Team,
in an application where space and cost is an issue: how cirtical do you estimate the 15nH inductor on the Output of the DCDC? (L5 in nrF51x22 ref-design...
hi
I am a beginner,i have two questions.
1、when i use the nrf52832 to read the inner temperature,i find the nrf_temp_init function is :
static __INLINE void nrf_temp_init...
Dear support team,
Can a Thread Boarder Router have Leader role? I have not seen any document which mention about it but all the Thread topology diagram have independent...
Hello,
I am not able to make the FDS work. Here is my setup
NRF51
SDK 12.3
S130 (2.0.1), i.e. s130_nrf51_2.0.1_softdevice.hex
Using peer manager as well...
We've been using bonding on our device for a while and have a lot of experience there, but we are now attempting to add "Just Works" pairing support that is a configuration...
nrf52832.
SDK14.2
Segger ES V3.34a
I am using nrf_drv_saadc_calibrate_offset() and find the next sample immediately after the calibration is erroneous.
There is...
Hi, I would like to use a nRF51 Dongle to connect to BLE devices and retrieve some data.
I already tried my scenario through nRF Connect for Desktop and it works, so I assume...
Hi,
I have a SPI sensor on an nRF51822, developed in mBED. To save battery power, I want to disable SPI while in ble.waitForEvent(). The only reference I could find is an...
Hi, I'm using Master Emulator API 2.1.7 and am having difficulties determining where I should be processing an acknowledge packet being returned from the slave after transmitting...
Hello,
I have been trying to have a central/peripheral device read UUIDs and RSSI values from surrounding peripherals using their advertisements and without actually connecting...
And base the nus service ,each peripheral can send message for cenrtal to other peripheral like mess.
I doubt it is possible because this example is base on the LED Button...
I'm building a smarthome application.
IPv6 over BLE not support mesh topology that is quite inconvenience to extend network. My teacher require me that this application...
