Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hey,
we want to change our product-bluetooth-chip for new products.
In the example the 16 Bit UUID overrides the byte 12 and 13 in the 128 bit ID. Where I could change...
Hello,
I am having interface nRF51 with RF receiver. Output of RF receiver connected with GPIO pin of nRF51.
How can I detect interrupt on gpio pin?
Thanks & Regards...
Hi,
I'm using Secure_Bootloader example of SDK 15.0.0 and I can't get the Logger module to work. I set NRF_LOG_ENABLED to 1, increased memory regions in make file, so the...
Can the esb bugfix timer (currently TIMER_3) be set to another un-used timer without any side effects? I need to implement the async uart from SDK15 and it uses TIMER_3 and...
Is there a simple example which supports LESC Just Works for peripheral mode only? The lesc_multirole example seems a bit too much since that also supports central role. I...
I am sampling 3 sensors using the ADC peripheral, clocking it once every 15us to sample the 3 sensors (3us acquisition time + 2us processing = 5us per channel).
I use the...
hi,
How can i set Destination Address to a particular Mesh Node. so that all message reach that particular Node Only.Since provisioner can set address while provisioning...
how to use app of mesh to send message to node ?
I already got the source code from web: https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library .
1\ i have add three...
I would like to put a nrf51822 device into system sleep (not off) mode and wake it up (not reset) with a GPIO transition from high to low. I used SDK(nRF5_SDK_12.2.0_f012efa...
Hello everybody, I tried to activate the PHY Coded in the UART Example from the SDK15.1.0 examples.
For this purpose, I have set NRF_BLE_SCAN_SCAN_PHY 4 in the sdk_config...
hello,we are developing NFC on NRF52832 recently,we want to use NFC as a label,T4T,but we have some problems as follows:
1、firstly,we want to develop NFCT by ourselves(not...
hello , i'am working actually on the timer of nRF52840 S140
my timer look like this:
but how to switch from millisecond resolution to microsecond resolution ? ( APP_TIMER_TICKS...
Hi!
I've try to made bootloader/recovery application that should to replace existing run-time application of the device. The F/W file for replacement placed in external...
Hello,
I am using Eclipse with ARM toolchain on ubuntu to buid my application with softdevice s132 api version 3.1.0. I managed to build on eclipse and merge softdevice...
