Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hello
SDK12.3, nRF51822
Example Gazelle from SDK works fine. If I use the softdevice (add ble_stack_init) then the program freezes in the nrf_gzll_enable
I want to do changes for firmware upgrade nrf52832 with SDK BLE_2.0.1 for the mesh.
I need DFU (Bootloader)UART for our application to upgrade nrf52832 firmware by the host...
Hi
I have written this code based on a sample from SDK12. The board is a pca10040 and nRF52832 chip. It seems like after disconnection from the master device the Softdevice...
Dear support team,
Channel survey (RSSI report for each data channels) are now available on S132v6. However, for users who need to use v4.0.2, is there alternative method...
I am using the Hackable Kit from Electronut labs and using their Bumpy , black magic probe alternative for programming. I would like to control a servo motor precisely at...
My code is on the multi-link example and it works well when I use another nrf52dk board as the "Nordic_Blinky" peripheral device, but it can't find my other BLE device.
...
Hello
I am running gls example on SDK14.2.
I paired after flashing program to my DK board, and then turn off power.
And turned on again, but i can't connect to my DK...
HI. I used a translator.
I am using the RNG example of SKD15.
I know that when I set the range of the random number to 1 byte, the number from 0 to 255 is generated. ...
I am using a Raspberry PI as a 6LoWPAN router, running Raspbian 9.4. Linux 4.14.34. Radvd 2.15.
I configured everything as described in IoT User Guide . I am using Miredo...
Hi,
As well know, the nrf51822 can only work either TX or RX mode at the same time.
Normally, the nrf51822 device is working in RX mode (by using function "nrf_esb_start_rx...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Dear all,
I am using an adafruit-nrf52-pro-feather (nrf52832) to run my project of detecting voice by this below scenario:
++ Setting up:
[PC] ==== USB cable ====...
To learn how to use FDS, I started by importing the code from the flash_fds example. My application is using peer manager and I got really strange errors until I realized...
Hello!
I am trying to set up the interface between an ARM Cortex-M4 andthe nRF8001. After RESET I see following data on the MISO line:
(turquoise=REQN/CS - pink=MOSI ...
Hi,
I would like to control the LEDs based on the PTM 215B switch by programming it using nRF52 DK. Where each button in the switch should turn one LED.
I am using...
