Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I am working on light switch demo of mesh SDK 2.1.
I am using nRF52832 board, SDK 15 for softdevice and segger embedded studio for programming the nRF52832.
I programmed...
Hello everyone,
I want to develop an android app, which is able to control multiple LED Lamps in a Mesh Network.
There is an app for provisioning provided by Nordic. Is...
Hi,
When I call sd_ble_gattc_read , I receive the BLE_GATTC_EVT_READ_RSP event very shortly after -- as expected. Within the event handler (registered with the Soft Device...
Hi,
I am considering using baluns instead of discrete components next to my nRF24LE1 QFN-24 chip since board space is at premium.
In application note AN4111 regarding...
I am new to Nordic and have a simple question. I followed the instructions about setting up manufacturer specific data with BLE_Template example here: https://devzone.nordicsemi...
in the middle of the code the MOSI change from idle low to high and resulting in writing 0xFF while reading over MOSI, resulting in getting wrong data. how can i change it...
Using SDK 15.0
Example project: examples/dfu/secure_bootloader/pca0040_ble/ses
Segger Embedded studio V3.50
File main.c line 52
#include "uECC.h" <------ "No such...
chip：52832
sdk：12.3 ble_app_template
when I measure the sleep current consumption use the nordic PPK
I found there is a 30ua peak in every 20ms，could you please tell...
I have some questions to Bluetooth mesh.
1. If I have a mesh Network is it possible to have a connection to a device over all the nodes? Or does mesh just support brodcast...
Hello!
I am a beginner.
I am trying to communicate with the SD card with SPI using nrf 52832.(BLE Nano v2)
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing...
Hi ,
SDK：15.1.0
example：proprietary_rf \ esb_ptx
Because there is no UART function in the example, I want to add it.
The picture is everything I added, is it missing...
Hi Devzone team,
In our SDK, say SDK15.0, there is a head file called "sdk_config.h". It contains a line which looks like below:
// <o> NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
Dear Sirs!
On one from 25 boards there is offset in ADC input about 30 ADC units. Vref = 0.6 V, Gain=6, 12 Bit ADC, oversampling 256 sample.
In other devices I do not...
