I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I’m working with a custom board using nRF7002 + nRF5340 + MX25R64 (SPI4) , and I’m trying to perform firmware updates over Wi-Fi using a firmware file hosted on an...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
I’m trying to run the TensorFlow Lite Micro example (zephyr_samples/hello_world) on my nRF5340DK using nRF Connect SDK 2.6.1, but I’m unable to build the project...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
Hi,
I am running ble_app_blinky example on nRF5280 custom board, it is giving me Error 133 (0x85): GATT ERROR . Since I have nrf52DK, I tried same example with SD 132 on...
Hello,
i am using the NRF52832 and the NRF52840 with different softdevices. Now I want to update the softdevices over the air and I need the SD Version strings of all the...
A bit more detailed: A bug has been detected on the device under development. It is connected with the fact that if you try to disconnect a connected device on an iMAC Catalina...
Hi
I am trying to install the SES toolchain on my PC (Win 8.1) following exactly the nRF Connect v3.2.0 Getting Started Assistant. When trying to "Open nRF Connect Project...
I am using a nRF52 DK to program an externally powered board with a NRF52811.
I am able to flash a blinky program onto the custom board successfully using the output .hex...
Just as the title says, I'm trying to measure an input pulse width using PPI and GPIOTE. I am currently measuring the pulse width using timer interrupts, but I would like...
Good day!
generic_ponoff_setup_server_init causes Mesh assert error.
If I delete reallocation of dtt and onoff servers' subscription lists everything goes fine.
What...
Hi!
I have been using LoRa for communication for my product. I'm looking into using BLE mesh.
I have a couple of hundred sensors, all 1-2m apart from each other. Here...
In this scheme we use 2 inductor in a serial connection. 15 nH + 10 uH. Total inductor = 10.015 uH. ??? Is really need to add this 15 nH inductor? For why? If we just short...
When calling access_model_subscription_list_dealloc() from models_init_cb() an assert is triggered in sublist_invalidate() due to mesh_config_entry_delete() returning NRF_ERROR_INVALID_STATE...
I have 3 Nordic nrf52840 USB dongles , several Particle Mesh Argons and have ordered an Arduino Nano 33 BLE Sense and have found the Adafruit Feather nRF52840 Express . All...
Hi,
Greetings!
I am facing a issue while updating firmware
My Setup:
SDK 16.0.0
SDK for Mesh 4.0.0
nRF52832
DFU: secure_bootloader_ble_s132_pca10040
Application...
I've gone through the forum and I've tried certain "solutions" but none of them work for me.
I've erased my device in SES multiple times, recreated the files for the service...
Hi all, I am checking the Uart central and peripheral projects, also the one with usbd and I have one question that may be obvious for you. How do you select the peripheral...
Hello,
I am using nrf52840 and SDK 16.0.0
I am doing some work with the calendar example and got some questions.
Q1.
Inside the main function in main.c file there...
