I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi
Two years ago our device was tested using nRFgo Studio 1.21.2.10 Direct Test Mode.
How can I know if the nRFgo software used BLE 4.2 or 5.0 during the tests? The only...
Hello,
We are making a custom application where we have several ble-mesh server nodes (nRF52832), and one of them connects to an Android app, acting as a proxy. The app...
Hi All,
I want explore BLE5 extended advertisement with nRF52832.
Using "ble_peripheral\ble_app_blinky" code from SDK16.0.0, facing " NRF_ERROR_INVALID_PARAM (7)" error...
Hi, I ported the TimeSync example devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices to the current SDK 16.0.0 and S140_nrf52_7.0.1_softdevice. But...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
There is the nRF52840 specifications sheet at the reference circuitry there is a pin 74 that is indicated as ground, what is this? 74 does not seem to line up with the method...
I don't know if this something I'm doing wrong, a Segger stupidity, or something else. I'm using SES and copied the examples/ble_central/ble_app_blink_c project to another...
I am struggling with excess current consupmtion using uart+fifo. It seems like ~300uA is drawn by UART and disabling via app_uart_close() doesn't help.
I have checked all...
HI,
I have nRF9160 modem DK. I am working a project based on http sample.
The LTE is initialized through the call:
w_lte_lc_init_and_connect();
But after ( in the...
Hi, In my current project I'm implementing an ANT Shared Channel topology, where in each channel period the master polls a slave with an acknowledge message and receives the...
Hello,
I can connect to LTE with the iBasis SIM that came with the nRF9160DK but have been unable to connect with any other SIM. Here is what happens in the LTE Link Monitor...
Hello,
I'm currently developing on a Adafruit nrf52840 express. I'm working under the impression I need to develop the code in C in order to use my code in mass production...
hi, i just purchased nrf52840 dongle, still new to use nordic components.
i have no idea on to use it as a beacon. already done the part in SES.
i want to make the dongle...
Hi Experts,
I have looked into the Mesh SDK for several days, i found one question is the device how to handle the same message they transmitted before after power reset...
