Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I am trying to setup a PPI channel to trigger the SAADC in simple mode. However, it appears as though the SAADC module is disabled after every read. I.e. if I write:
...
I am unable to flash the DK board facing issue " Failed to Connect to Target. No idcode detected. Please check connections and Target interface Type."
DK Board Details:...
I am using LSM9DS1 IMU, nRF52840 with SDK v16.0.0. I configured the IMU to raise an interrupt when the FIFO buffer be full by writing to register INT2_CTRL the value '0b00011000...
I can't see it!
https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Connect-for-desktop
The 'Downloads' section contains only the "host" native app - doesn...
I am trying to interface the BMM150 magnetometer with the nRF58240 MICRCONTROLLER, Iam able to establish the I2C connection and get the return value from the reg 0x40 and...
The stock LPN client for Mesh SDK v4.0.0 throws NRF_MESH_EVT_SAR_FAILED when replying to a publication set message via a friend node.
All code, reproduction data and log...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I want to write Serial number into...
Good morning....
I have an application that needs a remote control to communicate to six end nodes that are about 200' away in warehouses. It is a one-way communication...
Hi
the latest Errata sheet of the nRF52840 lists number [228] RADIO: No interrupt is generated for SYNC event.
Checking it, I was a little bit surprised finding actually...
i am using BLE template from examples BLE Peripheral and adding some custom characteristics and not changing any advertisement data. But the device is advertising with only...
Hi,
I want to set up visual code studio for development. I was able to successfully run the blinky app on PCA10040 board and also emulated PCA10040e example.
After this...
Hey folks,
I don't know what's the problem but I am really struggly to implement a simple UART into my heavily modified BLE Multilink Central Example (SDK16)..
Maybe...
Hi,
In my application, I would like to transfer data from MCU ---(UART#1)---> BLE#1(Peripheral) ---> BLE#2(Central) ---(UART#2)---> PC. I start my code based on ble_app_uart_pca10040e_s112...
I am using nrf52840 pdk for sniffing zigbee network. After flashing firmware from this link on board . After connecting nrf usb port to pc , windows giving error "Unknown...
