Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
we made a custom board using the chip nRF51822 and were able to use the template project in \..\examples\peripheral\template_project to make a button switch the led...
Hello,
I can't set the memory map into segger with a zephyr project.
For example for blinky project into ncs/zephyr/samples/blinky.
When I go to Project->Options, I...
Hello, we use the nRF24LE1 (24 pin) in a product, that is in production since many years. In order to process a FW change request I need to test the FW on a nRF24LE1 (48pin...
Dear Devzone
I have an NB-IoT application running on a Thingy:91, that wakes up every two minutes and sends a small package over TCP to a remote server. I'm using a Keithley...
I have been slogging my way through documentation and examples and have managed to create a beacon application using the development kit and Segger IDE. That said I am fumbling...
We are working on the GPS sample code found in the ncs\nrf\samples\nrf9160\gps folder of the nRF Connect SDK 1.1.0 tag in the repository.
The modem firmware version we...
If a record in a file with MESH_CONFIG_STRATEGY_ON_POWER_DOWN have been changed the NRF_MESH_EVT_CONFIG_STABLE is never emitted until mesh_config_power_down() is called. ...
Hi
I am working with nrf52832 development kit. I am trying to write device information service from central device to peripheral device.
I am successfully able to write...
Hello Devzone,
I've been using nRF52810, SoftDevice 112 (5.1.1), for a Mic recording application. What I'm trying to do is sample PDM MEMS mic data through PDM interface...
Dear Team,
I have nRF52 DK and nRF52840 DK, Can we program nRF9160 using nRF52 DK?
Please let me know the process and detailed wiring to program nRF9160.
Ashiq Moha...
Hi,
Good Day!
Statement of Problem: We use Li-Ion Battery in our application and would like to monitor a few variables such as Battery Voltage, Battery temperature & Discharge...
Hello, I'm trying to set up SPI communication with a sensor from my nrf5284_pca10056 running zephyr.
This is my prj.conf file:
This is my .overlay file:
And this...
I'm looking at the GPIO functions in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/peripherals/gpio.html , and looking at the function prototype...
Hi
I'm have and NRF52840 with a MPU9250 connected via TWI. The connection to the MPU9250 is successful, I can find its address on the bus (0x68).
I've implemented a very...
I am trying to add to an existing project gpiote
I have copied the code from the example project and tried to add all the files and changes to my sdk_config.h to match the...
