Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I could use some clarity on the legacy drivers/files, nrf,driving example applications inside SDK 16. Is it just too much work to clean up the examples with current drivers...
Hello everyone,
I am trying to implement UARTE on a custom board embedding an nRF52832 , as part of an upgrade from SDK 12 to SDK 15 . The nRF52832 is communicating via...
Hi,
A new modem firmware for nRF9160 has been released. Is it safe to update the modem firmware of Thingy: 91 to v1.1.1? We can download the firmware from nRF9160 SiP page...
Hi,
I'm trying to merge Serial and BLE DFU. I have followed this .
I have used BLE DFU example as base code and added Serial DFU dependencies.
I'm able to do BLE DFU...
HI,
i have made 3 customer board
they all use the same spi flash mx25v8006e
and the first two board have the spi pin : sck 3, miso 1,mosi 0,ss 2
but i change the design...
All I want to do is use the "Advertiser" tab in my nRF Connect android app and force it to broadcast using a custom 128-bit UUID.
I am struggling to figure out how to do...
I have tried combining a working SDK16_98a08e2 MPU6050 example with the SDCard example in the same SDK, however it seems they are incompatible because the MPU example uses...
Hi,
I am developing a device with nrf52840 soc, I need to know that there is any unique and unforgettable id in this chip that with that I could differentiate between...
Hi, Just wanted to pass this along... with the latest Raspbian (09/26/19) the thingy52 will consistently disconnect after about 90 seconds (+/- a few seconds). You can easily...
Hello,
I have two boards of nRF52840, one being central and the other is peripheral. On the central I've put the code from ble_app_multilink_central and on the peripheral...
Hello,
I see this type of query or GATT error has been asking continuously. I have gone through all the same Q&A but not able to solve my query. I have tried all the possible...
Hello Nordic support,
I was referring to the RTC example in nrf52 SDK where an interrupt is triggered on Compare Counter event. In the example, the interrupt is triggered...
I am trying to make custom BLE service to send the data from one nRF52832 to another nRF52832 but we followed the below tutorial "Bluetooth low energy Advertising, a beginner...
Hello,
We are developing a device that needs to get local binding info on init to see if it needs to send data or not to an on/off server in a remote device.
Is there...