Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Why does it say that the nRF51822 has 1Mb/s and 2Mb/s data rates if it doesn't?
Quote from devzone: "6 * 20 B* 1/0.0075 s = 16 kB/s = 128 kbps".
And its only for S110...
Hi there
I am having problems with uart app on SDK V7.2
I have dowloaded Keil and all of the other demo's seem to be working but this one is not.
It will not connect...
Hi. i have a little problem.
For start, i want to use the referance Layout found here link text with the hardware description file of PCA10004.
So there is a simple method...
Previously, I used to load and debug my programs.
after a few months,
Today when I setup the environment again, now I can only compile and generate hex files from Keil....
Hi,
Now I am try to use sd_flash_page_erase() to erase a flash page.
Before I call it, I already stop all interrupt but I always get a error message "NRF_ERROR_NO_MEM...
Hello,
I am working with nRF51822 development kit (s130 softdevice). I want to use one software interrupt for my custom application. Is there any software interrupt available...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...
Looking into the schematics, I could not find any uart or spi signals on the connectors. I am good in soldering, but I would not dare connecting wires to the nrf51422... ...
Hallo everyone!
I need very low consumption when BLE working. according to S110 SDS, BLE power profile section, when BLE in idle-connect, there is Ion+Irtc+Ix32k, same...
Use the spi_master_example_with_spi_slave in SDK6 to evaluate the SPI master module but fail.
No matter use the default pin assignment or re-assign, it does not give out...
I can't find in the documentation for the IoT the usual section about requirements for the start of user code, the start of user RAM, the max stack used and whether any heap...
I would like to be able to generate DTMF tones using PWM. I am very familiar with the process, having written code to do this several times on other devices. The DTMF will...
