At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I need a product that will allow me to connect a PC to a Bluetooth device through its Bluetooth connection. I will need to be able to send data bytes from my PC across the...
Hi everyone,
I am a beginner with Nordic SDK. I followed the " Getting Started Assistant" and then try to open asset_tracker project on step 4. During the opening I got...
Hello,
The fds.c fds_register() has suspicious usage of atomic variables.
It is first checked if there is space in the m_cb_table, then m_cb_table is modified and only...
Hi, I am trying to add timer information to the sending packet. We created some space(manuf_data) to store data. However, the problem is we do not know how to put actual-time...
Quick Summary: - Devices used: nRF52832 (Central), nRF52840 (Peripheral)
Example based on : BLE Scanner
Hi Team,
In my current application, based on a BLE Scanner Example...
Hi,
I'm using the latest SDK v16. I got the following error when call peer_manager_init()
<debug> nrf_ble_lesc: Initialized nrf_crypto. <debug> nrf_ble_lesc: Initialized...
Is there a recommended way to inspect the state of the heap? I haven't found anything obvious yet. I'd mainly like to know the amount free, the largest block, and perhaps...
Hi,
I start developing with ble_app_template and DK
I combine uart spi twi into it
It can connect to my phone(nRF Connect APP)and work fine on DK
However when i use...
We want use Nordic chips as the transfer medium for our data frames in mesh-like network.
So we don't need ATT,GATT,GAP,SDP,SMP and all high-level things.
As I can see...
The Device State Manager (DSM) will erase the flash if any of the following parameters have changed since last boot.
DSM_NONVIRTUAL_ADDR_MAX
DSM_VIRTUAL_ADDR_MAX
DSM_APP_MAX...
Hi,
I am using SDK15.3 very well with Keil 5.28 ( I cannot update because my licence for 5.28) When i try to change my sdk from 15 to 16, i have problem. I tried change...
I have a custom nRF52832 device acting as a peripheral and a central. Acting as a central device it reads the device information from a nRF52832 peripheral device. Now I want...
Hi
We've some trouble with the UART (not UARTE) of the nRF52840. We use a baudrate of 38400. Because of HW limitations and power constrains, we do either have flow control...
