Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I'm trying to write firmware for the nrf52840 that reads from a sensor and then sends data to a PC over BLE. Ultimately, I need the BLE link to achieve ~ 1.1 Mbps throughput...
Hi all,
I observe a connection supervision timeout (HMI error code 0x08) in my Nordic firmware with certain Android smartphones (controller).
Additional info regarding...
Hi. I'm just wondering if Nordic Semi engineers have done any tests with standard beacons (any particular beacon interval and test condition) application and compared current...
Hi teams,
We made BLE mesh custom boards based on nRF52833.
These nodes are configured to send broadcast messages for every 10 seconds.
Currently, these boards uses...
Hi Sir,
We would like to use the Radio test to do the basick TX/RX test in SDK 15.2
We use the nRF52840-DK for test and follow the CLI document .
1. We use two board...
Baud rate 460800, error code NRFX_ERROR_INTERNAL(1) occurred when the serial port received data。
I want to know how to avoid this problem, the current transfer rate is less...
Hi
We need the recv() be blocking until the full amount of requested data can be returned or the operation was timeout, how to achieve this?
I tried flag MSG_WAITALL but...
Hi. Can anyone think of a way to use the nRF52832 (probably Timer) to detect approximately 125KHz-150KHz variable square wave down to about a 1Hz resolution? I'd like to detect...
Is there any example for Directed Advertising? I'll design my NUS central and peripheral use Directed Advertising, because I would like to have other bluetooth devices connected...
I use this code below mentioned in this question https://devzone.nordicsemi.com/f/nordic-q-a/26030/how-to-reach-nrf52840-uarte-current-supply-specification
This can reduce...
Do you have any recommendations, tutorial, blog, or getting starting guide for a developer wanting to use Mesh and BLE on the same node? Any information would help. Does one...
Hi,
After long use of BLE communication I sometimes get return code 8 from sd_ble_gatts_hvx.
My questions:
1. This return code is cryptic. Is it associated with defined...
I am trying to configure the CryptoCell on an NRF52840 to use AES-CBC encryption with PKCS7 padding. When I call the following function, it returns SASI_AES_ILLEGAL_PADDING_TYPE_ERROR...
Board: nRF52833 DK
Version: 1.0.0 PCA10100
SD: s140
Env: Segger v4.52 (installed on 5/10 via Toolchain Manager)
Hello all...
I'm running into a problem with the...
I have to write this page in case of the application firmware update, so I have to unprotect it in the bootloader (in the nrf_bootloader_app_start_final() function). won't...
