I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi everyone,
I'm a beginner with nordic development and I managed to screw up my development kit. It started when I was trying to figure out the BLE blinky app with my IOS...
Hi,
I'm working on an IoT project with NRF52832 ( S132) . I need to connect this device to mqtt over 6LoWPAN (IPv6) and run it on a button cell battery CR2032 for as long...
HI,
I am trying to connect to our cloudmqtt account where the topics are dynamically created because of which is it not possible to pre-program a specific topic.
I would...
Hi,
it came to my attention that the inductor Murata LQP15MN3N9B02D (3.9nH) that is used in the antenna matching circuit of the nrf52832 reference design has become NRND...
Hi every one,
I'm a development product with chipset NRF52811, using soft device S112 and SDK 15.3.0.
My device will wake up and send data whenever I press the button...
Hello Nordic Team, I'm starting a project which consist in measure pressure in multiple points and send this data to central unit. At this point, using strain gauges with...
Hi,
I am using the Thingy 91 and I have a program, where I first read GPS, then switch to NBIoT Mode and then send the data to a server.
However if I switch the Antenna...
Hi, Nrf Connect was used as a central.When I send a data (Uart Service) from the app to the characteristic value of a Service (UUID:0x0002), the callback function of another...
Devices: nRF52840
Example: Light switch provisioner/client in one device
I have been looking into provisioner flash storage and am trying to understand at a fundamental...
Hi,
I flashed my 2 PCA10056 boards with light switch server and client respectively. As a provisioner, I am using my IPhone 6 wirh nRF`Mesh app.
After the provisioning...
Hi,
I am wondering how I would describe the capabilities of a device. Say, I were to develop a device that contains a light bulb and a fan. I could now use two elements...
Hi,
I am using Nrf Sdk Mesh V3.1.0 with softdeviceS132 and sdk board Nrf52832 and esp module
I want to implement Dfu process for my devices preset in mesh network and...
Hi everyone,
I am trying to include a header file into my project but the build solution fails with the error "No such file or directory"
I have placed my .c and .h file...
Hello,
From my software i get gps data and send to my webserver, periodically.
This works for some time then the system blocks! Nothing works anymore.
At first...
Dear team,
I have an understanding that BT Mesh is based on BT4.0 advertisement so even if we select a module with BLE5.0 the TX power will be less while using BT Mesh...
