Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi Devzone:
Where can I find full document on how to use nrf_power_gpregret_set?
Background: I am planing to do buttonless DFU without BLE but through usb cdc acm.
After...
Dear support team, we are trying to make the device ST IIS2DLPC (accelormeter) talk via SPI to the dev board PCA10040
We are using the evaluation board STEVAL-MKI191V1 wich...
Hello,
I am trying to build the lwm2m_client sample on my ubuntu 16.04 machine. I tried building for nrf9160_pca10090ns and nrf9160_pca20035ns The build fails with:
...
Hi,
I am using SEGGER/SEGGER Embedded Studio for ARM 4.12, I used Two working Examples ble_app_gatts_c_pca10040_s132 and flash_fstorage. I am getting these errors "undefined...
Hello,
For our project I'm using a LIS2DH (accelerometer) that is supposed to trigger an interrupt on its pin INT1 when a movement is detected.
I use nRF52832. Before...
Hi
I'm not familiar with C language, I tested the saadc example in SDK, it worked well in P0.02
But I dont see how they set CH[X].PSELP or CH[X].PSELN (V(p) and V(n))...
Hi
Using PCA 10040A , SDK 16.0.0 and Segger Studio.
I would like to generate a short accurate *** on a GPIO , probably 250 nano seconds duration. So I am looking at using...
Hello All,
my application should record acceleration data and time stamps.
After recording the data block from start to end should be transmitted.
I only know that...
Hello, guys.
In our current project, we need to periodically update AWS IoT Server with the data from local sensors. So far, thanks to the cloud_client example and your...
Hi
For a new project I'm looking for a cheap bluetooth chip. All my software resides in a PIC, because on PIC I have a lot of experience and I don't have the time to dedicate...
Hello all,
I am using NRF52840 and SDK 16 in central mode and added two UUID filters to the scan module for two different groups of peripherals . My application works fine...
Hi,
I am trying to send a test message in Server through mqtt and used the mqtt_simple example for that.
For the test I insert data_publish() function in main() like...
Hi!
The subject is most of the question.
I am beginning to customize the ble_app_template example, and when I build it, connect, and look at the advertising data, I see...
I want to connect NRF52840-pca10056 to PC via USB cable. I followed the docs but the OS doesn't detect the board automatically when plugged in. It only recognizes the board...
