Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello everybody,
I'm trying to flash an example code (let's say the blinky one) from the SDK (15.3) onto the Arduino Nano 33 BLE board.
I know that is possible to flash...
Hello,
I'm trying to resolve an issue in my project.
It appears there is a memory leak.
In logs I can find the error code : 0xBFED
Do you know what that code is? ...
Hi,
I recently had a problem about timestamp that it's all 0 on the RTT Viewer.
And i 'm based on the nRF5_SDK_15.2.0\examples\peripheral\rtc to check the timesteamp....
Hi Nordic
I have some issue When using NRF52832 central to connect the NRF52832 peripheral.
i am following the SDK15.3.0 ble_app_uart & ble_app_uart_c to deign the central...
Hi
I have a question about LXFO input on external low swing clock setting using nRF52832.
I can see the input specification of external low swing clock about only peak...
Hi,
I am currently developing a stationary BLE device. I am testing the nRF52840-dongle in combination with the pc-ble-driver. For that purpose, I am using the connectivity_4...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
Customers use nrf52810 flash program to store data, but want to know what flash start and end address can be written, please point out that you can refer to that document...
Dear Nordic Semiconductor
I am using device:
NRF51802 bluetooth 4.0
Product Introduction:
Features:
1.Adopt NRF51802 bluetooth 4.0 BLE SOC
2.ARM CORTEX-M0
3...
Hi , I use the pc-ble-driver to developer desktop tools, like nRF Connect. Unfortunately, I don't know Java. I‘ve tried to used examples that work(heart_rate_collector and...
Hello,
We use a custom interface board to program and run test programs on our series of tiny BLE modules based on nRF52xxx series (ISP1507, ISP1807, ISP1907).
Our interface...
Hello ,
The test of CPS/SEN/SPE/BI-04-C [Procedure Already In Progress] failed.
While this test, the tester sometimes received the unexpected ATT Disconnect which our...
