Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I can't find any documentation about this and my project depends on it.
Would it be possible to read the power usage in volts or any other value through a bluetooth connection...
Hi Nordics,
I have been trying out the SDK 15.2 DFU using serial / usb serial based on this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Modify the channel in the receiving mode, call the "nrf_esb_stop_rx" function in the "nrf_esb_event_handler" function, but what if the "if (m_nrf_esb_mainstate == NRF_ESB_STATE_PRX...
Hey Devs,
Would someone be able to tell me the power draw on the Thingy? How long will the onboard battery (1440 mAh) last on it?
Help is appreciated.
Thanks,...
Hi, I am developing firmware to run on a custom board using the nRF52810-CAAA chip. I need to meet very strict lower power consumption thresholds, and need to very precisely...
We are in development of a wearable ecg medical device. We want to add 4g low power capability. The device is a patch worn by patients 24/7 up to 30 days. Our current requirements...
Hi,
Is it possible to set CONFIG_HEAP_MEM_POOL_SIZE to be more than 16384?
I try to configure CONFIG_HEAP_MEM_POOL_SIZE = 94208 and when the heap allocated until 36830...
I have a device at -35 °C temperature, and sometimes I get the error "BLE_ERROR_INVALID_CONN_HANDLE" when in the ble_evt BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST. I'm using the...
For pairing key passing in ble_app_hrs, i have used the ble_app_gls example but it did not worked.
can anyone help me in how to pass pairing key issuse.
i have a question...
Hi! I am developing a network of temperature and humidity sensors, using nrf52832 and hts221 with the ide ses ... for this, I am using thingy 52 as a peripheral that sends...
Hi,
I have a project with NRF52832 and PCA10040 and SDK 16 and need to use both BLE and UART DFU. I can initialize and use them separately but I don't know how to use them...
Looking at the GPS driver source code, it seems there is no GPS hot start mode. In order to get the hot start working, do I have to modify the driver myself, or is there some...
have installed the software for Wireshark and I can see the interface in Wirshark, but I do not see and COM appearing in the Interface window nor does the sniffer appear as...
After many reboots, suddenly I got stuck at this error on every boot:
The data that's on the flash pages:
My mesh init params:
Using NRF52832, SDK 15.3.0, SD 132...
