Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi,
SW8 (MKH-22D14-G2-B) on my board is mechanically loose. When it is in on position, the board will intermittently power off and then back on. I did not find supply online...
Hi Guys
So I am new to this whole LWM2M protocol, so my knowledge is not that good. I have the following problem. I want to start the LWM2M_client sample with the following...
In the existing nRF5x SDK, there is a type 2 and a type 4 NFC library which can be used on nRF52 chipsets. With the introduction of zephyr and the new dual-core chipset based...
Hi,
Here's my setup:
Custom board built with nRF52840
nRF5_SDK_for_Thread_and_Zigbee_v4
Segger Embedded Studio for ARM v3.52
I have built a Zigbee Coordinator...
Hi!
About my application:
SDK 16.0.0.
FreeRTOS and SoftDevice s140.
Peripheral role (buttonless dfu without bonding)
Central role NUS_C
When incoming connection...
Hi,
If I edit a project config file (.conf) how do I get SES to rebuild the project makefiles via west?
The only way I've found is to reload the project. Which seems a...
Hi teams,
Recently, I made a custom board based on nRF52833 DK.
It works fine until now, and most of things works well.
But, I cannot make the board to show logs in...
I can see advertising packets of a device using an nRF51822 in Wireshark (example packet capture here https://imgur.com/a/maV6kbb) . But can't see them in nRF Connect on Android...
Hello,
I'm using the peer_manager in a GATT server project, after a first bond was created, I want the peripheral (GATT server) to advertise with ADV_DIRECT_IND, once the...
Hi,
I started development of nRF51822 with Keil(V6) / nRFgo / Segger etc..
I got SDK and exxample from here ( https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v6.x...
Hi ,
I use the C language and pc-ble-driver to development a PC tool. Now I can use handle to establish connection. How can I use the pc-ble-driver update the target device...
I'm developing an Android app which should read sensor values of a BLE sensor on a high frequency (at least 25hz). The nRF Toolbox is receiving the values on the Notify property...
This document mentions the Tile service works with SoftDevice S132:
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v16.0.0/lib_tile.html
I'm wondering if the service...
I used USB CDC ACM for NRF52840. and I want to prepare the testing the usb pins in the production.
Do you have any suggestion on how to quickly test the VBUS, D+, D- on...
Hi. I've bought myself two Nrf52840 dongles. And I want to develop a zigbee network. When I tried to flash a light_switch example to one of my dongles I found out that there...
