Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi Nordics,
I have been trying out the SDK 15.2 DFU using serial / usb serial based on this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Modify the channel in the receiving mode, call the "nrf_esb_stop_rx" function in the "nrf_esb_event_handler" function, but what if the "if (m_nrf_esb_mainstate == NRF_ESB_STATE_PRX...
Hey Devs,
Would someone be able to tell me the power draw on the Thingy? How long will the onboard battery (1440 mAh) last on it?
Help is appreciated.
Thanks,...
Hi, I am developing firmware to run on a custom board using the nRF52810-CAAA chip. I need to meet very strict lower power consumption thresholds, and need to very precisely...
We are in development of a wearable ecg medical device. We want to add 4g low power capability. The device is a patch worn by patients 24/7 up to 30 days. Our current requirements...
Hi,
Is it possible to set CONFIG_HEAP_MEM_POOL_SIZE to be more than 16384?
I try to configure CONFIG_HEAP_MEM_POOL_SIZE = 94208 and when the heap allocated until 36830...
I have a device at -35 °C temperature, and sometimes I get the error "BLE_ERROR_INVALID_CONN_HANDLE" when in the ble_evt BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST. I'm using the...
For pairing key passing in ble_app_hrs, i have used the ble_app_gls example but it did not worked.
can anyone help me in how to pass pairing key issuse.
i have a question...
Hi! I am developing a network of temperature and humidity sensors, using nrf52832 and hts221 with the ide ses ... for this, I am using thingy 52 as a peripheral that sends...
Hi,
I have a project with NRF52832 and PCA10040 and SDK 16 and need to use both BLE and UART DFU. I can initialize and use them separately but I don't know how to use them...
Looking at the GPS driver source code, it seems there is no GPS hot start mode. In order to get the hot start working, do I have to modify the driver myself, or is there some...
have installed the software for Wireshark and I can see the interface in Wirshark, but I do not see and COM appearing in the Interface window nor does the sniffer appear as...
After many reboots, suddenly I got stuck at this error on every boot:
The data that's on the flash pages:
My mesh init params:
Using NRF52832, SDK 15.3.0, SD 132...
I have designed my own board, based around the nRF9160 but unfortunately I am unable to connect to an LTE network.
I am running the at_client code and using LTE Link Monitor...
Hello guys I am using nrf52840 interfacing analog sensors like potentiometer and accelerometer. This is not related to nrf, but I want to design a simple ADC filter that I...
