When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
I have the NRF_CCM peripheral setup to encrypt packets on-the-fly. I can verify packets are properly encrypted when the payload size is 27 bytes or smaller. However, anything...
Hi,
I have created a configuration based on usbd_app_uart example where both usbd and softdevice are enabled on my device as soon as the device is turned on. When I transmit...
Hi,
I am developing a simple application that utilizes a light switch client example for NRF52832 with SDK15.0 and Mesh 4.0.
I am facing a problem when using the FDS module...
What could be the reasons that cause DFU Bootloader BLE not working with nRF Connect on PC (while it works with nRF Connect on iOS)? I have had various problem with nRF Connect...
Hello
I am using Seggar Embedded Studio for ARM V3.4 and nRF_SDK 12.3.0. I am trying to understand interrupts and interrupt handlers.
The interrupt request for Watchdog...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I have nRf52840 and I am trying to add a timer to examples\ble_peripheral\ble_app_uart...
Hi,
Setup:
I’m sending ble packages with around 80 Hz from an server (nrf52832 sdk 15.2) to a client device ( nrf52840 sdk 15.2)
One Ble package consist of several...
This is probably a simple question for an experienced nRF developer.
I have a demo going where I can read or write any of four characteristics I have set up on my peripheral...
Hi all, i have two units of a custom board project that i made.
In the first board, I plugged the pins in the right position as you can see in the figure below, a). nRFgo...
Hello everyone,
How to read Scan Response in contentiously in every 5 seconds in my ble_app_uart_c. i can advertise ibeacon and Scan Response data both in same code but...
I am using SDK V15.2 and opened the SES example for dtm. I modified RXD and TXD pins since i use a custom board based on the nRF52832.
When debugging the example on the...
I need to implement DFU in a Unity3D application. I have tried to integrate the Android SDK library that you have on github. They are not integrating very well.
I have a...
