hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Peripheral: SDK13.1 nRF52832
I don't want to change ConnectionParamaeter of Periperal by ConnectionUpdate request from Central. Can Periperal ignore ConnectionUpdate from...
Hej folks,
after quite some research on how to get Nordic UART and Linux together, here's as far as I got: Discover the device with hcitool lescan And - in theory - connect...
Hi all
Looking at the compatibility matrix, we understand that the following SoftDevices and SDK versions are compatible:
SDK 15.0 <---> SoftDevice S140 6.0.0
SDK 15...
Hello,
I am developing an app that uses Xamarin.Forms to communicate with BLE devices equipped with Nordic chips.
It works fine on IOS, but Android doesn't.
Android...
I have a custom board using the nRF52832 QFAA with SDK 15.3.0 and SoftDevice132 6.1.1. I'm also using an external 32kHz crystal for the softdevice clock. There are two hardware...
Hello,
I'm having issues connecting over TLS more than a single time. Using the nrf/samples/nrf9160/https_client works fine.
However, if you modify it to connect more...
Hello, I am trying to use the timer peripheral via registers only, however I am running into issues when I setup two timers and they activate at the same time. Here are my...
Hi There,
I am developing an IoT portable sensor which needs to operate across Europe Zone 1.
Talking with different MVNO it seems that NB-IoT and M1 coverage across...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I need clarification if softdevice uses RTC and if so is the Errata 20 applicable...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0)
I am looking into Erratas and working on the possible workarounds. However...
HI,ALL！
I use official routine development NRF52832，
NordicSDK\nRF52\nRF5_SDK_16\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput\pca10040\s132...
Hey!
I'm using mesh sdk 4.0, nrf5-sdk 16.0 and run the serial example.
currently I successfully provision 2 light server with the ipython interface, and to configure them...
I am trying to do service discovery using the discovery manager library on any BLE device I connect to my central. I start the service with bt_gatt_dm_start(conn, NULL, &discovery_cb...
Is there any app available that can use to track lost/retransmitted packets and get some log?
I’m trying to find best position for a nRF52840 module with chip antenna without...
Hello everyone,
I work on a project with a custom board and e NRF52840 on it.
I work with the SDK15.2.0, the SoftDevice s140 and FreeRTOS.
The BLE function well but...
