I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
I'm currently developping a peripheral. This one uses Peer Manager module to handle pairing. This peer manager is configured properly with pm_sec_params_set (as far...
Hi,
I was working with the SPI interface of nrf52DK microcontroller boards and wanted to know if there is a way to change the timings of the low and high levels of the Slave...
I'm designing a solution based on a series of nodes that senses data and has to send it wirelessly to a hub. Each hub must be able to receive data from about 4 to 8 nodes...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Please tell me the operation when garbage collection is executed. The setting values of FDS are shown below for reference.
We...
nrf52832 master wakes up the slave under sleep?nrf52832 slave wakes up the host under sleep?
My boss wants very low power consumption. I think the host can wake up the slaves...
Hi,
When I used the same command, I was only able to read the 5 bytes correctly. The Most higher byte does not match.
C:\Program Files\Nordic Semiconductor\nrf-command...
Hi
I would like to know if it is possible to to run the Nrf905 chips on 5v logic level without damaging the chip ? i see many people playing with arduino and these chips...
Hi, my customized board was using nRF52840 with 15.3 ver SDK.
And we want to make the DFU download process part can progress in the application.
(such as background download...
Hi Sir
I have used sdk 11.0.0 to develop my bluetooth application but i am facing some issue, so want enable debug logs, but i am not getting where to enable it plz help...
Hi!
I'm interested in trying out hci_usb sample of nRF Connect SDK with Nordic's Link Layer.
With following changes to application configuration I'm able to compile the...
Hi there,
I am trying the asset tracker example on nrf9160DK-HW 0.9.0.
While I have been able to get GPS fix within 20-30 seconds using the "GPS sample" example... I've...
Hello, I am starting to upload my code to some new Raytac MDBT40 modules, and am starting with the soft device of course.
I am using uVision V5.28.0.0
I can not upload...
We have devices that we want to turn on at some future date. This means that when they're deployed they should somehow get real time, calculate when they will wake up, and...
I am seeing that the default manufacturer BLE is defaultly F5:41:36, received experimentally from inspecting data from the nRF52832... Now, of course there is sd_ble_gap_address_set...
Hi,
I have a custom Nrf52810 board. It was working fine and was advertising well. Somehow ble chip got damaged and I needed to replace it.
After I replaced, I can do debug...
