Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello there, I need to ask if these two; NRF M 24L01+1712AB , NRF M 24L01+1609AH (one with external Antenna) are still supported and have official libraries , and if not supported...
I'm trying to advertise on the coded phy, but SDK 16 seems to have a block in place against doing this when you use S340. I can obviously edit this, but I don't normally edit...
After Installing JLink 6.62 it offered a firmware update for the connected JLink. I performed the update (Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jan 21 2020 17...
Hello,
I´m trying to connect the nRF9160-DK to the nRF cloud, using the asset tracker application. I was able to build and flash the application. But the DK can not connect...
Hello,
We are working through an issue which we found recently on the nrf sdk. The following is what is occuring:
We have two GPIO interrupts configured for low accuracy...
Hi... folks .. i am using nRF52840 development kit , i need to control the two servo motor using ble commands . I need to control the angle and speed of two motors , suggest...
Hello,
When I power our customer-designed nRF52832-based electronics I see the ingoing suply current (at 3.1V) rising in about 3 seconds up to 55 mA (!), then decreasing...
Hi, I have a problem with uart disable function (app_uart_close();). I started from ble_app_uart example, and I want to disable uart when nobody is connected to the Ble device...
Hi,
I have a similar problem to the case: ( devzone.nordicsemi.com/.../having-a-problem-with-preprocessor-options) with not being able to access the preprocessor options...
Hi,
As per the workaround of these errata its mentioned that "This code is already present in the latest sytem_nrf52.c file."
What does the latest mean here? Is there...
Hi,
I have two questions, one regarding nrfjprog and one regarding pynrfjprog:
How do I write content to a specific address of the flash using nrfjprog? Specifically...
I want to build custom commissioner app on nRF52840 DK. But when I'm running:
The error is OT_ERROR_ALREADY. I don't understand why, I am not invoking this method multiple...
I am using the nRF9160dk development board and I could not find a test or example for the internal RTC. could you provide a simple example of using the internal RTC.
