Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I'm trying to enable the CMSIS Wizard on SES 4.42a. I followed the instructions and pasted the required xml into tools.xml, saved the file and restarted SES.
This is my...
Hi Support,
I need to use another eSIM not the iBasis, because the company those not have roaming coverage in Bulgaria.
Question: If I use a IoT eSIM card Telefonica...
I want to send a one byte payload from the nrf24l01+ (Sparkfun dev board), to nrf52840 DK using the example esb_prx. How should I configure the nrf24 registers to make this...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...
Hello everyone. I'm creating a setup function to configure LSM9DS1 accelerometer and gyroscope by writing to the corresponding registers as shown below
Although this code...
I use sdk16.0 and nrf52832.
Can you give me an example of nrf52832 timeslot example ? thank you.
I read timeslot on DevZone,but many routines are missing files, resulting...
Writing an app for the Arduino Nano 33 BLE Sense:
https://store.arduino.cc/usa/nano-33-ble-sense
Basically I am reading all sensors on the Sense board (temperature, humidity...
I have programmed a Nordic Thingy 91 with lte_ble_gateway, and when I send command from the cloud to the device, an NRF_CLOUD_EVT_RX_DATA event is called, however evt->param...
Dear all,
I want to implement multiple functions with only one power button, including: 1. Power on/off, Long press to turn on, long press to turn off; 2. Functional response...
I am trying to connect nrf52840 dongle to multiple peripherals(nrf51822) ,so far i combined multilink_c example with uart_c and i can connect and read rssi value of only 1...
Sorry, my English is very bad.
I think I can only express my problem in Chinese.
在使用异步串口时，使用uart_rx_enable()设置的超时时间和真实发生UART_RX_RDY事件的时间相差巨大
using async serial port...
Hi,
We need to interface camera (0.3nrf52840MP to 2MP) with nrf52840 for a new product development. For evaluation purpose, is there any off the shelf camera module which...
I'm trying to add a timer to the usb_cdc_acm example to send a periodic text messages with the timer. I'm building on an Adafruit nRF52840 Feather Express board using Segger...
Hi ,
I am trying to parse the manufacturer specific data that a beacon is advertising.
I can read successfully the company_id but unable to read the "specific data " ...
